Exhaust Sensor Lines - Remove and Install - Exhaust Gas Venturi
`
C15 and C18 On-Highway Engines
[UENR3300]
AIR INLET AND EXHAUST SYSTEM
EXHAUST GP
C15 and C18 Industrial Engines
Exhaust Elbow - Remove and Install - Clean Emissions Module Inlet
C15 and C18 Industrial Engines
Exhaust Elbow - Remove and Install - Clean Emissions Module Outlet
C15 and C18 On-Highway Engines
Exhaust Sensor Lines - Remove and Install - Exhaust Gas Venturi
C15 and C18 On-Highway Engines
Exhaust Manifold - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 207-1601 | Rubber Lubricant | 1 |
Start By:
- Remove the fumes disposal group.
- Remove the cooled exhaust gas pressure sensors.
- Remove bolts (1) and (2) and remove tube assembly (5).
- Remove clamp (3) and remove exhaust gas venturi (4).
Show/hide table
| |
| Illustration 1 | g03436702 |
- Install the exhaust gas venturi in the reverse order of removal.
- Use Tooling (A) on all O-ring seals that were removed.
- Tighten clamp assembly (3) to a torque of
8.5 ± 2 N·m (75 ± 18 lb in) .
Information System:
Procedure to Return the Fuel Filter for Certain Caterpillar Equipment{1260, 1261, 1274}
2013/10/21
Improved Case Assembly is Used on Certain CX31-P600 Petroleum Transmissions {3064}
C4.4 Engines for Caterpillar Built Machines
Crankshaft - Spheroidal Graphite Iron (SGI) Crankshaft
440-0842 Major Engine Overhaul Foundational Kit for 3512 Engines{1000}
12M Series 3, 140M Series 3, 160M Series 3, 140, 150 and 160 Motor Graders
System Schematic
2013/10/31
A New Pump Bracket is Now Used on Certain C12 Marine Engines Equipped with a Bronze Impeller Pump {1371}
2013/10/28
New Engine Software Is Used for Certain C280 Marine Engines {1901, 1920}
14L Motor Grader Machine Systems
Bank Valve - Install - Rear Frame
14L Motor Grader Machine Systems
Bank Valve - Disassemble - Rear Frame
14L Motor Grader Machine Systems
Bank Valve - Assemble - Rear Frame
440-0216 Major Engine Overhaul Foundational Kit for 3512B and 3512C Engines{1000}
2013/10/03
The Hydraulic Tank Relief Valve Assembly Has Been Improved on Certain Cat Machines {4332, 4332, 5056, 5056, 5057, 5118}
374F and 390F Excavators and 390F MHPU Mobile Hydraulic Power Unit
Alarm - Test
374F Excavator Machine Systems
Hydraulic System Warm-Up
440-0928 Major Engine Overhaul Foundational Kit for 3512C Engines{1000}
C15 and C18 On-Highway Engines
Nozzle Heater Harness - Remove and Install
C9 Engine
Maintenance Interval Schedule
390F Excavator
Counterweight Removal and Installation
2013/12/12
New Exhaust Shield Assemblies Are Used on Certain 3408 and 3412 Engines {1107}
131-5051 Dataview Group and Dataview Portable Tech Station Group{0374, 0599, 0701, 0709}
374F and 390F Excavators and 390F MHPU Mobile Hydraulic Power Unit
Connector Contact Description
PM820, PM822, and PM825 Cold Planer
Rotor Drive (Planetary) Oil Sample - Obtain
CX31-P600 Petroleum Transmission
Transmission Cooling System
2013/10/02
Improvements for Products and Systems Connected to Product Link {7606}