Fuel Transfer Pump - Install
`
C7 Engines for Caterpillar Built Machines
[RENR9218]
C7 Engines for Caterpillar Built Machines
Fuel Transfer Pump - Remove
C7 Engines for Caterpillar Built Machines
Water Pump - Assemble
FUEL SYSTEM
PUMP GP-FUEL TRANSFER
C7 Engines for Caterpillar Built Machines
Fuel Transfer Pump - Remove
C7 Engines for Caterpillar Built Machines
Fuel Transfer Pump - Install
1.1. Installation Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 3E-8006 | Bolt | 1 |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Position fuel transfer pump (2) on the unit injector hydraulic pump. Be sure to align the drive tang of the fuel transfer pump to the drive slot in the end of the pump shaft.
- Install tie bolts (4). Tighten the bolts to a snug fit.
- Remove Tooling (A) that is located in the upper left hole and install remaining tie bolt (1) to a snug fit.
- Install bolts (3) for fuel transfer pump (2). Tighten the bolts to a snug fit.
- Start in the lower left corner of the unit injector hydraulic pump and tighten tie bolts (4) to a torque of
28 ± 2 N·m (21 ± 1 lb ft) in a crisscross pattern. Torque the bolts again. - Tighten bolts (3) to a torque of
8.0 ± 0.4 N·m (71 ± 4 lb in) .
Show/hide table
| |
| Illustration 1 | g01123057 |
End By:
- Install the unit injector hydraulic pump. Refer to Disassembly and Assembly, "Unit Injector Hydraulic Pump - Install".
Information System:
C7 Engines for Caterpillar Built Machines
Fuel Transfer Pump - Remove
345C Excavator Hydraulic System
Stick Drift Reduction Valve
2004/11/01
New Injectors and New Flash Files are Now in Production {1290, 7620}
SR4 and SR4B Generators and Control Panels
Maintenance Interval Schedule - Standby
SR4 and SR4B Generators and Control Panels
Maintenance Interval Schedule - Standard
325D and 329D Excavators
Engine Starting with Auxiliary Start Receptacle - If Equipped
C32 Marine and Marine Generator Set Engines
Cooling System
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines
Refill Capacities and Recommendations
C32 Marine and Marine Generator Set Engines
Air Inlet and Exhaust System
C27 PET GEN SET Electric Power Generation and C27 KNOCKDOWN K Petroleum Power Train Package
Fuel Related Components in Cold Weather
3412E Petroleum Engine
Battery - Test
120M, 12M, 140M, 140, 150, 160M and 160 Motor Graders
Power Train
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines
Alternator and Fan Belts - Inspect/Adjust
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines
Engine Crankcase Breather - Replace
C27 and C32 Engines
Finding Top Center Position for No. 1 Piston
C9 Industrial Engines
Cooling System
2004/12/01
Improved Alignment of a Coolant Tube {1380}
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines
Turbocharger - Inspect - If Equipped
C32 Marine Engines
Fuel System
3508B, 3512B and 3516B Generator Set Engines
Engine Oil Pan - Remove
3508B, 3512B and 3516B Generator Set Engines
Engine Oil Pan - Install
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines
Fuel System - Prime
C0.5, C0.7, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines
Fuel System Secondary Filter - Replace
3508B, 3512B and 3516B Generator Set Engines
Crankshaft - Remove