Cylinder Liner - Install
`
3512B and 3516B Engines
[KENR8171]
BASIC ENGINE
CYLINDER BLOCK GP
3408E and 3412E Engines for Caterpillar Built Machines
Bearing Clearance - Check
3508C, 3512C and 3516C Marine Engines
Camshaft Bearings - Remove
3508C, 3512C and 3516C Marine Engines
Camshaft Bearings - Install
3500 Engines
Cylinder Liner - Remove
3512B and 3516B Engines
Cylinder Liner - Install
3500 Engines
Connecting Rod Bearings - Remove and Install
3508C, 3512C and 3516C Marine Engines
Crankshaft Main Bearings - Install
1.1. Installation Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| B | 2P-8260 | Cylinder Liner Installer | 1 |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Check the cylinder liner projection. Refer to Testing and Adjusting, "Cylinder Liner Projection - Inspect".
Show/hide table
Illustration 1 g01004993 - Apply liquid soap on the grooves for O-ring seals (3) and on the O-ring seals. Install the O-ring seals on cylinder liner (1). Also, coat the cylinder block bore for the cylinder liner with liquid soap.
- Dip filler band (2) in clean engine oil. Immediately install the filler band onto the cylinder liner. Install the cylinder liner into the cylinder block before the filler band can expand. Ensure that the marks that are on the cylinder liner and the cylinder block are aligned.
Show/hide table
Illustration 2 g01120837 - Use Tooling (B) to press cylinder liner (1) into the cylinder block.
End By:
- Install the pistons and the connecting rod assemblies. Refer to Disassembly and Assembly, "Pistons and Connecting Rods - Install".
Information System:
3500 Engines
Cylinder Liner - Remove
2004/11/01
Improved Mounting of the Power Distribution Box {7426}
365B Excavators Hydraulic System
Swing Bearing Movement - Measure
C11 and C13 Engines for Caterpillar Built Machines
Throttle Switch Circuit - Test
C-10 Petroleum Engine
Air Inlet and Exhaust System
345B Excavator Hydraulic System
Swing Bearing Movement - Measure
3412E Petroleum Engine
Flywheel Housing
C11 and C13 Engines for Caterpillar Built Machines
User Defined Shutdown Input Circuit - Test
3508B, 3512B and 3516B Generator Set Engines
Cylinder Head - Remove
12M, 140M, 160M, 140, 150 and 160 Motor Graders Braking and Hydraulic Fan System
Valve Replacement Kit - Diverter Valve and Relief Valve
320B Excavator Hydraulic System
Swing Bearing Movement - Measure
C11 and C13 Engines for Caterpillar Built Machines
Engine Temperature Sensor Open or Short Circuit - Test
2004/11/01
Circuit Breakers - Steps to Consider When Resetting {1420}
G3524 and G3532 Tandem Maintenance{7002}
3600 to 3600 Electronic Unit Injector (EUI) Upgrade{1000, 1250}
C-10 Petroleum Engine
Cooling System
C-10 Petroleum Engine
Finding Top Center Position for No. 1 Piston
C-10 Petroleum Engine
Fuel System - Prime
3412E Petroleum Engine
Finding Top Center Position for No. 1 Piston
325D and 329D Excavators
Hydraulic System Oil Level - Check
C-10 Petroleum Engine
Inlet Manifold Pressure - Test
325D and 329D Excavators
Hydraulic System Oil Filter (Return) - Replace
C-10 Petroleum Engine
Cooling System - Check - Overheating
C-10 Petroleum Engine
Cooling System - Test