Rocker Shaft - Disassemble
`
3508C, 3512C and 3516C Marine Engines
[KENR6055]
3508C, 3512C and 3516C Marine Engines
Rocker Shaft and Push Rods - Install
3508C, 3512C and 3516C Marine Engines
Rocker Shaft - Assemble
BASIC ENGINE
VALVE MECHANISM GP
3508C, 3512C and 3516C Marine Engines
Rocker Shaft and Push Rods - Install
3508C, 3512C and 3516C Marine Engines
Rocker Shaft - Disassemble
3508C, 3512C and 3516C Marine Engines
Rocker Shaft - Assemble
3508C, 3512C and 3516C Marine Engines
Inlet and Exhaust Valve Springs - Remove and Install
3508C, 3512C and 3516C Marine Engines
Valve Mechanism Cover Base - Remove and Install
1.1. Disassembly Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 1P-0510 | Driver Group | 1 |
Start By:
- Remove the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Remove".
- Slide shaft (2) out of rocker arm (1). If necessary, remove spring pin (3) from the shaft.
Show/hide table
Illustration 2 g01120059 - Remove jam nut (4) from adjustment screw (6). Remove the adjustment screw from rocker arm (1).
- Remove button (9) from socket (7). Remove retaining ring (8) from button (9).
- Use a hammer and a punch to remove socket (7) from rocker arm (1).
- Use Tooling (A) to remove sleeve bearing (5) from the rocker arm.
Show/hide table
| |
| Illustration 1 | g01120055 |
Information System:
C11 and C13 Engines for Caterpillar Built Machines
Engine Fan Control Solenoid Circuit - Test
C7 and C9 On-Highway Engines
0094-01 Low Fuel Pressure Warning (63)
C7 and C9 On-Highway Engines
0094-11 Low Cranking Fuel Pressure (63)
345C MHPU Mobile Hydraulic Power Unit Hydraulic System
Pilot Valve (Swing Parking Brake)
C12 Marine Engines
Auxiliary Water Pump - Disassemble
345C MHPU Mobile Hydraulic Power Unit Hydraulic System
Swing Motor
C11 and C13 Engines for Caterpillar Built Machines
Electrical Power Supply Circuit - Test
C11 and C13 Engines for Caterpillar Built Machines
Cat Data Link Circuit - Test
C11 and C13 Engines for Caterpillar Built Machines
5 Volt Engine Pressure Sensor Supply Circuit - Test
C-10 Petroleum Engine
Lubrication System
C9 Marine Generator Set
Safety Messages
3508C, 3512C and 3516C Marine Engines
Rocker Shaft and Push Rods - Install
3508C, 3512C and 3516C Marine Engines
Rocker Shaft - Assemble
C11 and C13 Engines for Caterpillar Built Machines
Engine Pressure Sensor Open or Short Circuit - Test
C12 Marine Engines
Auxiliary Water Pump - Assemble
C11 and C13 Engines for Caterpillar Built Machines
Engine Temperature Sensor Open or Short Circuit - Test
320B Excavator Hydraulic System
Swing Bearing Movement - Measure
12M, 140M, 160M, 140, 150 and 160 Motor Graders Braking and Hydraulic Fan System
Valve Replacement Kit - Diverter Valve and Relief Valve
3508B, 3512B and 3516B Generator Set Engines
Cylinder Head - Remove
C11 and C13 Engines for Caterpillar Built Machines
User Defined Shutdown Input Circuit - Test
3412E Petroleum Engine
Flywheel Housing
345B Excavator Hydraulic System
Swing Bearing Movement - Measure
C-10 Petroleum Engine
Air Inlet and Exhaust System
C11 and C13 Engines for Caterpillar Built Machines
Throttle Switch Circuit - Test