Auxiliary Water Pump - Disassemble
`
C12 Marine Engines
[RENR9405]
C12 Marine Engines
Valve Mechanism Cover Base - Remove and Install
C12 Marine Engines
Auxiliary Water Pump - Assemble
COOLING SYSTEM
PUMP GP-WATER
C12 Marine Engines
Water Pump - Remove
C12 Marine Engines
Water Pump - Disassemble
C12 Marine Engines
Water Pump - Assemble
C12 Marine Engines
Auxiliary Water Pump - Remove
C12 Marine Engines
Auxiliary Water Pump - Disassemble
C12 Marine Engines
Auxiliary Water Pump - Assemble
1.1. Disassembly Procedure
Start By:
- Remove the auxiliary water pump. Refer to Disassembly and Assembly, "Auxiliary Water Pump - Remove".
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 1P-0510 | Driver Gp | 1 |
| B | 1P-1857 | Retaining Ring Pliers | 1 |
| C | 1P-1855 | Retaining Ring Pliers | 1 |
| D | 8H-0663 | Bearing Puller Gp | 1 |
| E | 8S-6470 | Forcing Screw | 1 |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove elbow (1) and elbow (3).
- Remove cover (2).
- Remove gear (4) and bracket (5).
Show/hide table
Illustration 2 g01119837 - Remove quad ring seal (7). Use Tooling (E) to remove impeller (6) from the shaft.
Show/hide table
Illustration 3 g01119842 - Remove cam liner (9) and the pin from housing (8).
- Remove quad ring seal (10) and wear plate (11) from housing (8).
- Use Tooling (C) to remove retaining ring (12).
- Remove washer (13).
Show/hide table
Illustration 4 g01119860 - Remove seal assembly (15) from shaft assembly (14).
Note: Place a mark on the housing and the body assembly for correct alignment at assembly.
Show/hide table
Illustration 5 g01119864 - Remove bolts (16). Separate housing (8) from body assembly (17).
Show/hide table
Illustration 6 g01119867 - Use Tooling (A) to remove seal (18) from housing (8).
Show/hide table
Illustration 7 g01119869 - Remove seal (19) from shaft assembly (14).
Show/hide table
Illustration 8 g01119871 - Use Tooling (B) to remove retaining ring (20).
- Use a soft hammer to remove shaft assembly (14) from body assembly (17).
Show/hide table
Illustration 9 g01119877 Show/hide table
Illustration 10 g06435481 - Use Tooling (A) to remove seal (21) and washer (22) from body assembly (17).
Show/hide table
Illustration 11 g06435493 - Use Tooling (D) and a suitable press to remove bearing (23) from shaft assembly (14).
Show/hide table
Illustration 12 g06419912 - Use Tooling (C) to remove retaining ring (26) from shaft assembly (14).
Show/hide table
Illustration 13 g06419909 - Remove spacer (25).
Show/hide table
Illustration 14 g06419908 - Use Tooling (D) and a suitable press to remove bearing (24) from shaft assembly (14).
Show/hide table
| |
| Illustration 1 | g01119793 |
Information System:
345C MHPU Mobile Hydraulic Power Unit Hydraulic System
Swing Motor
C11 and C13 Engines for Caterpillar Built Machines
Electrical Power Supply Circuit - Test
C11 and C13 Engines for Caterpillar Built Machines
Cat Data Link Circuit - Test
C11 and C13 Engines for Caterpillar Built Machines
5 Volt Engine Pressure Sensor Supply Circuit - Test
C-10 Petroleum Engine
Lubrication System
C9 Marine Generator Set
Safety Messages
3508C, 3512C and 3516C Marine Engines
Rocker Shaft and Push Rods - Install
C-10 Petroleum Engine
Fuel System
C11 and C13 Engines for Caterpillar Built Machines
System Configuration Parameters
12M and 140 Motor Grader
Lifting and Tying Down the Machine
Installation of the 262-5465 Check Valve Kit or the 266-4455 Check Valve Kit {1714}
Installation of the 262-5465 Check Valve Kit or the 266-4455 Check Valve Kit {1714}
3500 Engines
Electronic Control Module (Engine) - Remove and Install
345C MHPU Mobile Hydraulic Power Unit Hydraulic System
Pilot Valve (Swing Parking Brake)
C7 and C9 On-Highway Engines
0094-11 Low Cranking Fuel Pressure (63)
C7 and C9 On-Highway Engines
0094-01 Low Fuel Pressure Warning (63)
C11 and C13 Engines for Caterpillar Built Machines
Engine Fan Control Solenoid Circuit - Test
3508C, 3512C and 3516C Marine Engines
Rocker Shaft - Disassemble
3508C, 3512C and 3516C Marine Engines
Rocker Shaft - Assemble
C11 and C13 Engines for Caterpillar Built Machines
Engine Pressure Sensor Open or Short Circuit - Test
C12 Marine Engines
Auxiliary Water Pump - Assemble
C11 and C13 Engines for Caterpillar Built Machines
Engine Temperature Sensor Open or Short Circuit - Test
320B Excavator Hydraulic System
Swing Bearing Movement - Measure
12M, 140M, 160M, 140, 150 and 160 Motor Graders Braking and Hydraulic Fan System
Valve Replacement Kit - Diverter Valve and Relief Valve
3508B, 3512B and 3516B Generator Set Engines
Cylinder Head - Remove