Water Temperature Regulators - Remove
`
3508C, 3512C and 3516C Marine Engines
[KENR6055]
3508C, 3512C and 3516C Marine Engines
Water Pump - Assemble
3508C, 3512C and 3516C Marine Engines
Water Temperature Regulators - Install
COOLING SYSTEM
REGULATOR GP-TEMPERATURE
3508C, 3512C and 3516C Marine Engines
Water Temperature Regulators - Remove
3508C, 3512C and 3516C Marine Engines
Water Temperature Regulators - Install
1.1. Removal Procedure
Show/hide table
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Drain the cooling system until the level of the coolant is below the water temperature regulator housing.
Show/hide table
Illustration 1 g06123162 - Disconnect hose assembly (1) and hose assembly (5) from water temperature regulator housing (6).
- Disconnect tube assembly (2) from water temperature regulator housing (6). Remove the O-ring seal from the tube assembly.
- Remove tube assembly (3) from the water temperature regulator housing.
- Remove bolts (4). Remove water temperature regulator housing (6).
- If necessary, remove bolts (7) and remove outlet elbow (8) from the water temperature regulator housing. Remove the gasket from the outlet elbow.
Show/hide table
Illustration 2 g06123164 - Remove water temperature regulator (12) and gasket (9). Remove lip seal (10) from water temperature regulator housing (6).
Show/hide table
Illustration 3 g06123166 - Remove vent valve (12) from the water temperature regulator housing.
Information System:
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines
J1939 Bridge
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines
Diagnostic Capabilities
Installation Procedures for the 259-4020 Voltage Regulator Assembly (for use with Caterpillar Power Modules Equipped with Legacy Switchgear that Utilize the 131-5374 Annunciator Module Control Group ){4467}
3508B, 3512B and 3516B Generator Set Engines
Turbocharger - Install
C15 and C18 Engines for Caterpillar Built Machines
Crankshaft - Install
C15 and C18 Engines for Caterpillar Built Machines
Crankshaft - Remove
3508B, 3512B and 3516B Generator Set Engines
Turbocharger - Remove
C15 and C18 Engines for Caterpillar Built Machines
Pistons and Connecting Rods - Install
120M, 12M, 140, 140M, 150, 14M, 160M, 160 and 16M Motor Graders Secondary Steering System
Operational Checks
C9 Marine Generator Set
Fuel System Secondary Filter - Replace
3412E Petroleum Engine
General Information
C15 and C18 Engines for Caterpillar Built Machines
Pistons and Connecting Rods - Remove
3508C, 3512C and 3516C Marine Engines
Water Temperature Regulators - Install
120M, 12M, 140, 140M, 150, 14M, 160M, 160 and 16M Motor Graders Secondary Steering System
Relief Valve (Secondary Steering) - Test
349F and 352F Excavators
Swing Drive Oil - Change
PL1000E Communication ECM
Electrical Connector - Inspect
C15 and C18 Engines for Caterpillar Built Machines
Electric Starting Motor - Remove and Install
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines
Electronic Control Module (ECM) - Configure
3126B Petroleum Engine
Can Not Reach Top Engine RPM
3412E Petroleum Engine
Electronic Unit Injector - Test
3412E Petroleum Engine
Electronic Unit Injector - Adjust
C-10 Petroleum Engine
General Information
3500 Engines
Turbocharger - Assemble - Type 2
3500 Engines
Turbocharger - Disassemble - Type 2