Valve Mechanism Cover - Remove and Install
`
C15 and C18 Engines for Caterpillar Built Machines
[RENR8261]
C15 and C18 Engines for Caterpillar Built Machines
Crankshaft Front Seal - Install
C15 and C18 Engines for Caterpillar Built Machines
Valve Mechanism Cover Base - Remove and Install
BASIC ENGINE
VALVE MECHANISM GP
C15 and C18 Generator Set Engines
Rocker Arm and Shaft - Install
C15 and C18 Engines for Caterpillar Built Machines
Valve Mechanism Cover - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines
Valve Mechanism Cover Base - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines
Rocker Arm and Shaft - Remove
C15 and C18 Engines for Caterpillar Built Machines
Valve Actuator (Variable) - Remove
C15 and C18 Engines for Caterpillar Built Machines
Valve Actuator (Variable) - Install
1.1. Removal Procedure
2.1. Installation Procedure
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove breather tube (1) from the valve mechanism cover.
- Remove bolts (2), valve mechanism cover (3), and the seal.
Show/hide table
| |
| Illustration 1 | g01046114 |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install the seal onto valve mechanism cover (3). Position valve mechanism cover (3) on the valve mechanism cover base. Install bolts (2). Tighten the bolts in a numerical sequence to a torque of
18 ± 3 N·m (13 ± 2 lb ft) . - Install breather tube (1) on the valve mechanism cover.
Show/hide table
|
| |
| Illustration 2 | g01046114 |
Show/hide table
| |
| Illustration 3 | g00579295 |
Information System:
C11 and C13 Engines for Caterpillar Built Machines
Sensors and Electrical Connectors
3508B, 3512B and 3516B Generator Set Engines
Exhaust Manifold - Remove and Install
C15 and C18 Tier 4 Final Engines
Turbocharger - Inspect
C15 and C18 Engines for Caterpillar Built Machines
Crankshaft Front Seal - Install
C15 and C18 Engines for Caterpillar Built Machines
Crankshaft Front Seal - Remove
3126B Petroleum Engine
Piston and Rings
3412E Petroleum Engine
Piston and Rings
C15 and C18 Generator Set Engines
Crankshaft Rear Seal - Install
G3300 Engines
Maintenance Log
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines
Service Tools
C15 and C18 Engines for Caterpillar Built Machines
Air Inlet and Exhaust System
3126B Petroleum Engine
Cylinder Head Valves
C15 and C18 Engines for Caterpillar Built Machines
Valve Mechanism Cover Base - Remove and Install
C-10 Petroleum Engine
Valve Mechanism Cover
C3.3 and C4.4 Generator Sets
Fuel System Primary Filter/Water Separator - Drain
C15 and C18 Engines for Caterpillar Built Machines
Rocker Arm and Shaft - Remove
C15 and C18 Tier 4 Final Engines
Cooling System - Check - Overheating
C15 and C18 Engines for Caterpillar Built Machines
Camshaft - Remove
C15 and C18 Engines for Caterpillar Built Machines
Camshaft - Install
C15 and C18 Engines for Caterpillar Built Machines
Pistons and Connecting Rods - Remove
3412E Petroleum Engine
General Information
C9 Marine Generator Set
Fuel System Secondary Filter - Replace
120M, 12M, 140, 140M, 150, 14M, 160M, 160 and 16M Motor Graders Secondary Steering System
Operational Checks
C15 and C18 Engines for Caterpillar Built Machines
Pistons and Connecting Rods - Install