Crankshaft Front Seal - Remove
`
C15 and C18 Engines for Caterpillar Built Machines
[RENR8261]
C15 and C18 Engines for Caterpillar Built Machines
Electronic Unit Injector - Install
C15 and C18 Engines for Caterpillar Built Machines
Crankshaft Front Seal - Install
BASIC ENGINE
CRANKSHAFT GP
3408E and 3412E Engines for Caterpillar Built Machines
Bearing Clearance - Check
C15 and C18 Generator Set Engines
Crankshaft Rear Seal - Install
C15 and C18 Engines for Caterpillar Built Machines
Crankshaft Front Seal - Remove
C15 and C18 Engines for Caterpillar Built Machines
Crankshaft Front Seal - Install
C15 and C18 Engines for Caterpillar Built Machines
Crankshaft - Remove
C15 and C18 Engines for Caterpillar Built Machines
Crankshaft - Install
C15 and C18 Engines for Caterpillar Built Machines
Crankshaft Rear Seal - Remove
1.1. Removal Procedure
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Tool | Part Number | Part Description | Qty |
| A | 1U-7600 | Slide Hammer Puller | 1 |
Start By:
- Remove the vibration damper and the pulley. Refer to Disassembly and Assembly, "Vibration Damper and Pulley - Remove and Install".
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Use Tooling (A) or a punch and hammer in order to puncture three or more holes in wear sleeve (2).
- Use Tooling (A) to remove the wear sleeve.
- Use Tooling (A) or a punch and hammer in order to puncture three or more holes in crankshaft front seal (1).
- Use Tooling (A) to remove the crankshaft front seal.
Show/hide table
| |
| Illustration 1 | g01044861 |
Information System:
3126B Petroleum Engine
Piston and Rings
3412E Petroleum Engine
Piston and Rings
C15 and C18 Generator Set Engines
Crankshaft Rear Seal - Install
G3300 Engines
Maintenance Log
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines
Service Tools
C15 and C18 Engines for Caterpillar Built Machines
Air Inlet and Exhaust System
3126B Petroleum Engine
Cylinder Head Valves
2007/04/30
A New Oversized Oil Pump Idler Gear Shaft is Available {1304}
3508B, 3512B and 3516B Generator Set Engines
Aftercooler - Remove and Install
2005/09/05
Improvements to Turbocharger and Exhaust Manifold Groups {1052, 1059, 1061}
C27 and C32 Industrial and Petroleum Engines
Air Lines
G3406 and G3412 Generator Sets
Voltage Regulators
C15 and C18 Engines for Caterpillar Built Machines
Crankshaft Front Seal - Install
C15 and C18 Tier 4 Final Engines
Turbocharger - Inspect
3508B, 3512B and 3516B Generator Set Engines
Exhaust Manifold - Remove and Install
C11 and C13 Engines for Caterpillar Built Machines
Sensors and Electrical Connectors
C15 and C18 Engines for Caterpillar Built Machines
Valve Mechanism Cover - Remove and Install
C15 and C18 Engines for Caterpillar Built Machines
Valve Mechanism Cover Base - Remove and Install
C-10 Petroleum Engine
Valve Mechanism Cover
C3.3 and C4.4 Generator Sets
Fuel System Primary Filter/Water Separator - Drain
C15 and C18 Engines for Caterpillar Built Machines
Rocker Arm and Shaft - Remove
C15 and C18 Tier 4 Final Engines
Cooling System - Check - Overheating
C15 and C18 Engines for Caterpillar Built Machines
Camshaft - Remove
C15 and C18 Engines for Caterpillar Built Machines
Camshaft - Install