Electronic Unit Injector Sleeve - Remove
`
C27 and C32 Generator Set Engines
[RENR9716]
C27 and C32 Generator Set Engines
Electronic Unit Injector - Remove
C27 and C32 Generator Set Engines
Electronic Unit Injector - Install
BASIC ENGINE
CYLINDER HEAD GP
C27 and C32 Generator Set Engines
Camshaft Bearings - Remove
C27 and C32 Generator Set Engines
Camshaft Bearings - Install
C27 and C32 Generator Set Engines
Electronic Unit Injector Sleeve - Install
C15 and C18 Generator Set Engines
Inlet and Exhaust Valve Guides - Remove and Install
C15 and C18 Generator Set Engines
Inlet and Exhaust Valve Springs - Remove and Install
C15 and C18 Generator Set Engines
Inlet and Exhaust Valves - Remove and Install
C27 and C32 Generator Set Engines
Electronic Unit Injector Sleeve - Remove
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Tool | Part Number | Part Description | Qty |
| A | 9U-6891 | Injector Tool Group | 1 |
Start By:
- Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit Injector - Remove".
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Drain the coolant from the cooling system into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".
Show/hide table
Illustration 1 g01043124 - Install Tooling (A) in electronic unit injector sleeve (1).
- Tighten the nut on Tooling (A) until the electronic unit injector sleeve is pulled free of the cylinder head.
Show/hide table
Illustration 2 g01073635 - Remove O-ring seals (2) and O-ring seal (3) from electronic unit injector sleeve (1).
Information System:
C15 and C18 Engines for Caterpillar Built Machines
Electronic Unit Injector - Install
C27 and C32 Generator Set Engines
Electronic Unit Injector - Remove
3508C, 3512C and 3516C Marine Engines
Water Pump - Assemble
3508C, 3512C and 3516C Marine Engines
Water Pump - Disassemble
C32 Commercial Engines
Heat Exchanger
C15 and C18 Engines for Caterpillar Built Machines
Fuel Transfer Pump - Remove
12M, 140M, 160M, 140, 150 and 160 Motor Graders Hydraulic and Steering System
Hydraulic Tank
C27 and C32 Industrial and Petroleum Engines
Flywheel Housing
390F MHPU Mobile Hydraulic Power Unit
Engine Oil Level - Check
390F MHPU Mobile Hydraulic Power Unit
Cooling System Coolant Sample (Level 1) - Obtain
C15 and C18 Engines for Caterpillar Built Machines
Fuel System
C27 and C32 Generator Set Engines
Flywheel
C9.3 Tier 4 Final Engines
Valve Mechanism
390D Excavator
Access Door and Cover Locations
G3406 and G3412 Generator Sets
Voltage Regulators
C27 and C32 Industrial and Petroleum Engines
Air Lines
2005/09/05
Improvements to Turbocharger and Exhaust Manifold Groups {1052, 1059, 1061}
3508B, 3512B and 3516B Generator Set Engines
Aftercooler - Remove and Install
2007/04/30
A New Oversized Oil Pump Idler Gear Shaft is Available {1304}
3126B Petroleum Engine
Cylinder Head Valves
C15 and C18 Engines for Caterpillar Built Machines
Air Inlet and Exhaust System
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines
Service Tools
G3300 Engines
Maintenance Log
C15 and C18 Generator Set Engines
Crankshaft Rear Seal - Install