Air Inlet Manifold - Remove and Install
`
3508B, 3512B and 3516B Generator Set Engines
[RENR5060]
AIR INLET AND EXHAUST SYSTEM
MANIFOLD GP-INLET
3500B Engines
Air Inlet Manifold - Remove and Install
3508B, 3512B and 3516B Generator Set Engines
Air Inlet Manifold - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure
Start By:
- Remove the aftercooler. Refer to Disassembly and Assembly, "Aftercooler - Remove and Install".
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove bolts (2). Pry elbow (3) away from air inlet manifold (1).
- Remove bolts (4).
- Attach a suitable lifting device to air inlet manifold (1). The weight of the 3508B air inlet manifold is approximately
48 kg (105 lb) .Note: The weight of the 3512B air inlet manifold is approximately
54 kg (120 lb) . The weight of the 3516B air inlet manifold is approximately91 kg (200 lb) . - Remove air inlet manifold (1). Remove the O-ring seal from elbows (3).
Show/hide table
| |
| Illustration 1 | g01114292 |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install the O-ring seal on elbows (3).
- Attach a suitable lifting device to air inlet manifold (1). The weight of the 3508B air inlet manifold is approximately
48 kg (105 lb) .Note: The weight of the 3512B air inlet manifold is approximately
54 kg (120 lb) . The weight of the 3516B air inlet manifold is approximately91 kg (200 lb) . - Position air inlet manifold (1) and install bolts (4).
- Install the O-ring seal on elbow (3).
- Position elbow (3) and install bolts (2).
Show/hide table
|
| |
| Illustration 2 | g01114292 |
End By:
- Install the aftercooler. Refer to Disassembly and Assembly, "Aftercooler - Remove and Install".
Information System:
C27 and C32 Engines for Caterpillar Built Machines
Crankshaft
C27 and C32 Engines for Caterpillar Built Machines
Cylinder Liner
2004/11/01
Improved Turbocharger Groups {1052}
C12 Marine Engines
Valve Mechanism Cover Base - Remove and Install
3126B Petroleum Engine
Cooling System - Check - Overheating
3508C, 3512C and 3516C Marine Engines
Engine Oil Filter Housing - Assemble
3508C, 3512C and 3516C Marine Engines
Engine Oil Filter Housing - Disassemble
C12 Marine Engines
Marine Transmission Oil Cooler - Remove and Install
345C MHPU Mobile Hydraulic Power Unit Hydraulic System
Solenoid Valve (Proportional Reducing) - Power Shift System
C27 and C32 Industrial and Petroleum Engines
Exhaust Manifold
3508C, 3512C and 3516C Marine Engines
Engine Oil Filter Housing - Install
3508C, 3512C and 3516C Marine Engines
Engine Oil Filter Housing - Remove
3054 and 3056 Marine Generator Sets
Maintenance Interval Schedule - 3054 Turbocharged Marine Generator Set Engine
3054 and 3056 Marine Generator Sets
Maintenance Interval Schedule - 3056 Turbocharged Marine Generator Set Engine
C27 and C32 Generator Set Engines
Piston and Rings
320D Excavator
Boom, Stick and Bucket Operation
C0.5 and C0.7 Industrial Engines
Engine Starting
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines
General Information
345C MHPU Mobile Hydraulic Power Unit Hydraulic System
Pilot Valve (Joystick)
3500 Engines
Water Pump - Remove
3500 Engines
Water Pump - Install
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines
Features
12M, 140, 140M, 150, 160M and 160 Motor Graders Hydraulic and Steering System
Blade Cushion - If Equipped
G3520C and G3520E Generator Set Engines
Cooling System - Landfill Application