Engine Oil Filter Housing - Install
`
3508C, 3512C and 3516C Marine Engines
[KENR6055]
3508C, 3512C and 3516C Marine Engines
Engine Oil Filter Housing - Remove
3508C, 3512C and 3516C Marine Engines
Engine Oil Filter Housing - Disassemble
LUBRICATION SYSTEM
FILTER GP-ENGINE OIL
3508C, 3512C and 3516C Marine Engines
Engine Oil Filter Housing - Remove
3508C, 3512C and 3516C Marine Engines
Engine Oil Filter Housing - Install
3508C, 3512C and 3516C Marine Engines
Engine Oil Filter Housing - Disassemble
3508C, 3512C and 3516C Marine Engines
Engine Oil Filter Housing - Assemble
1.1. Installation Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 138-7573 | Link Bracket | 2 |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Attach a suitable lifting device on oil filter housing support (11). The weight of oil filter housing support (11) is approximately
70 kg (155 lb) . Position oil filter housing support (11) and install bolts (10). - Install Tooling (A) and a suitable lifting device on engine oil filter housing (9). The weight of engine oil filter housing (9) is approximately
35 kg (77 lb) . Position engine oil filter housing (9) and install bolts (8). Remove Tooling (A).Show/hide table
Illustration 2 g01113751 - Position plate (7) and install bolts (6).
- Install spacers (5) and bolts (4) to secure tube assembly (3).
Show/hide table
Illustration 3 g01113749 - Install the O-ring seal on adapter (2). Install the adapter and install bolts (1).
- Disconnect the oil pressure sensors.
- Check the oil level. Maintain the oil level at the "FULL" mark. Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change" for the correct filling procedure.
Show/hide table
| |
| Illustration 1 | g01113831 |
End By:
- Install the fuel filter housing. Refer to Disassembly and Assembly, "Fuel Filter Housing - Install".
Information System:
3508C, 3512C and 3516C Marine Engines
Engine Oil Filter Housing - Remove
345C MHPU Mobile Hydraulic Power Unit Hydraulic System
Accumulator (Pilot)
345C Excavator Hydraulic System
Displacement Change Valve
345C Excavator Hydraulic System
Travel Parking Brake
345C Excavator Hydraulic System
Travel Motor
C15 and C18 Engines for Caterpillar Built Machines
Engine Speed/Timing Sensor Circuit - Test
Cat</SUP> Digital Voltage Regulator
Parameter Viewing and Configuration (Caterpillar PC Software)
C7 and C9 On-Highway Engines
Poor Acceleration or Response
3508B Engine for Caterpillar Built Machines
Refrigerant Compressor
3508C, 3512C and 3516C Marine Engines
Fuel Transfer Pump - Assemble
3508C, 3512C and 3516C Marine Engines
Fuel Transfer Pump - Disassemble
120M, 12M, 140, 140M, 150, 14M, 160M, 160 and 16M Motor Graders Secondary Steering System
Secondary Steering Hydraulic System
C27 and C32 Industrial and Petroleum Engines
Exhaust Manifold
345C MHPU Mobile Hydraulic Power Unit Hydraulic System
Solenoid Valve (Proportional Reducing) - Power Shift System
C12 Marine Engines
Marine Transmission Oil Cooler - Remove and Install
3508C, 3512C and 3516C Marine Engines
Engine Oil Filter Housing - Disassemble
3508C, 3512C and 3516C Marine Engines
Engine Oil Filter Housing - Assemble
3126B Petroleum Engine
Cooling System - Check - Overheating
C12 Marine Engines
Valve Mechanism Cover Base - Remove and Install
2004/11/01
Improved Turbocharger Groups {1052}
C27 and C32 Engines for Caterpillar Built Machines
Cylinder Liner
C27 and C32 Engines for Caterpillar Built Machines
Crankshaft
3508B, 3512B and 3516B Generator Set Engines
Air Inlet Manifold - Remove and Install
3054 and 3056 Marine Generator Sets
Maintenance Interval Schedule - 3054 Turbocharged Marine Generator Set Engine