Inlet and Exhaust Valve Seat Inserts - Remove and Install
`
C12 Marine Engines
[RENR9405]
C12 Marine Engines
Cylinder Head - Install
C12 Marine Engines
Marine Transmission Oil Cooler - Remove and Install
BASIC ENGINE
CYLINDER HEAD GP
3176C and 3196 Engines For Caterpillar Built Machines
Camshaft Bearings - Install
3176C and 3196 Industrial Engines
Camshaft Bearings - Remove
3176C and 3196 Marine Engines
Inlet and Exhaust Valve Guides - Remove and Install
C12 Marine Engines
Electronic Unit Injector Sleeve - Remove
C12 Marine Engines
Electronic Unit Injector Sleeve - Install
C12 Marine Engines
Inlet and Exhaust Valve Springs - Remove and Install
C12 Marine Engines
Inlet and Exhaust Valves - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure
Removal Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 166-7441 | Valve Seat Extractor Tool | 1 |
Start By:
- Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust Valves - Remove and Install".
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Use Tooling (A) in order to remove valve seat inserts (1) .
Show/hide table
 | |
| Illustration 1 | g01110502 |
Installation Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| B | 1U-9170 | Valve Seat Driver | 1 |
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Lower the temperature of new valve seat inserts (1) .
Show/hide table
 | |
| Illustration 2 | g00513644 |
- Use Tooling (B) in order to install the new valve seat inserts in the cylinder head assembly.
End By: Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust Valves - Remove and Install".
Information System:
C6.6 Marine Generator Set
Generator Lead Connections
G3520C and G3520E Engines
Accessory Drive
120M, 12M, 140, 140M, 150, 14M, 160M, 160 and 16M Motor Graders Secondary Steering System
Location of Electrical Components
120M, 12M, 140, 140M, 150, 14M, 160M, 160 and 16M Motor Graders Secondary Steering System
Secondary Steering System
C12 Marine Engines
Cylinder Head - Install
C12 Marine Engines
Cylinder Head - Remove
Field Installation of the 263-8162 Sleeve Kit (INJECTOR){1713}
C12 Marine Engines
Heat Exchanger - Remove
C12 Marine Engines
Engine Oil Filter Base - Assemble
C12 Marine Engines
Engine Oil Filter Base - Disassemble
C6.6 Marine Generator Set EMCP3
General Information
120M, 12M, 140, 140M, 150, 14M, 160M, 160 and 16M Motor Graders Secondary Steering System
Location of Hydraulic Components
C9 Marine Generator Set
Control Panel - Standard
EMCP3
Engine Overspeed Warning
EMCP3
Engine Underspeed Warning
C6.6 Marine Generator Set
Voltage Regulators
C15 and C18 Industrial Engines
Fuel Temperature Sensor - Remove and Install
C15 and C18 Industrial Engines
Fuel Pressure Sensor - Remove and Install
C9 Industrial Engines
Electronic Control System Components
G3516C and G3516E Gas Engines
Crankcase Breather
Installation Procedure for 257-4183 Injector Wiring Harness Kit {1408}
On-Highway Engines Electronic PTO Installation and Application Guide
PTO Shutdown Timer - Test
On-Highway Engines Electronic PTO Installation and Application Guide
PTO Switch Circuit - Test
On-Highway Engines Electronic PTO Installation and Application Guide
PTO Switch ON Lamp Circuit - Test