Lifter Group - Remove and Install
`
C12 Marine Engines
[RENR9405]
C12 Marine Engines
Electric Starting Motor - Remove and Install
C12 Marine Engines
Engine Oil Filter Base - Disassemble
BASIC ENGINE
VALVE MECHANISM GP
C12 Marine Engines
Valve Mechanism Cover - Remove and Install
C12 Marine Engines
Lifter Group - Remove and Install
C12 Marine Engines
Valve Mechanism Cover Base - Remove and Install
1.1. Removal Procedure
2.1. Installation Procedure
Removal Procedure
Start By:
- Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Remove".
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Place identification marks on the lifter assembly for installation.
- Remove bolts (1) and lifter assembly (2) .
Show/hide table
 | |
| Illustration 1 | g01109091 |
- Remove the following items from lifter shaft (3) : bracket assemblies (4), valve lifters (5) and unit injector lifters (6) .
Show/hide table
 | |
| Illustration 2 | g01109092 |
Installation Procedure
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Lubricate the lifter shaft with clean engine oil prior to assembly.
Show/hide table
| | |
| Illustration 3 | g01109092 |
- Install the following items on lifter shaft (3) : bracket assemblies (4), valve lifters (5) and unit injector lifters (6) .
- Place lifter assembly (2) on the engine and install bolts (1). Tighten the bolts to a torque of 30 ± 3 N·m (22 ± 2 lb ft).
Show/hide table
| | |
| Illustration 4 | g01109091 |
Note: Immerse the entire lifter assembly in clean engine oil prior to installation on the engine.
End By: Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".
Information System:
EMCP3
System Operation
C12 Marine Engines
Electric Starting Motor - Remove and Install
3054 and 3056 Marine Generator Sets
Maintenance Interval Schedule - 3054 Naturally Aspirated Marine Generator Set Engine
120M, 12M, 140, 140M, 150, 14M, 160M, 160 and 16M Motor Graders Secondary Steering System
Introduction
Cat</SUP> Digital Voltage Regulator
Parameter Viewing and Configuration (Caterpillar Electronic Technician)
12M, 140, 140M, 150, 160M and 160 Motor Graders Hydraulic and Steering System
Hydraulic and Steering System
C12 Marine Engines
Crankshaft Gear - Remove and Install
C12 Marine Engines
Crankshaft - Install
C9 Industrial Engines
Electric Starting Motor
12M, 140, 140M and 160M Motor Graders Braking and Hydraulic Fan System
Brake Accumulator
C12 Marine Engines
Crankshaft - Remove
C12 Marine Engines
Crankshaft Main Bearings - Install
120M, 12M, 140, 140M, 150, 14M, 160M, 160 and 16M Motor Graders Secondary Steering System
Location of Hydraulic Components
C6.6 Marine Generator Set EMCP3
General Information
C12 Marine Engines
Engine Oil Filter Base - Disassemble
C12 Marine Engines
Engine Oil Filter Base - Assemble
C12 Marine Engines
Heat Exchanger - Remove
Field Installation of the 263-8162 Sleeve Kit (INJECTOR){1713}
C12 Marine Engines
Cylinder Head - Remove
C12 Marine Engines
Cylinder Head - Install
120M, 12M, 140, 140M, 150, 14M, 160M, 160 and 16M Motor Graders Secondary Steering System
Secondary Steering System
120M, 12M, 140, 140M, 150, 14M, 160M, 160 and 16M Motor Graders Secondary Steering System
Location of Electrical Components
G3520C and G3520E Engines
Accessory Drive
C6.6 Marine Generator Set
Generator Lead Connections