Electrical Connectors
`
C15 and C18 Engines for Caterpillar Built Machines
[RENR5033]
C15 and C18 Engines for Caterpillar Built Machines
Programmable Parameters
C15 and C18 Engines for Caterpillar Built Machines
Alternator Problem
1.1. Connectors for the Electronic Control Module (ECM)
2.1. Injector Connectors
3.2. Connectors at the Valve Cover
4.2. Connector at the Injector
5.1. Sensor Connectors
6.2. Analog Sensor Connector (active)
7.2. Analog Sensor Connector (passive)
8.2. Connectors for the Termination Resistor
9.2. Engine Speed/Timing Connector
10.2. Ampseal Connector (typical)
11.2. Deutsch Connectors (typical)
Connectors for the Electronic Control Module (ECM)
Show/hide table
| |
| Illustration 1 | g02141017 |
|
Locations of the components at the ECM (1) P2 ECM connector (ECM side) (2) P1 ECM connector (ECM side) (3) P2 ECM connector (harness side) (4) P1 ECM connector (harness side) (5) ECM | |
Show/hide table
| |
| Illustration 2 | g01746753 |
Show/hide table
| |
| Illustration 3 | g01717773 |
|
Typical injector | |
Analog Sensor Connector (active)
Show/hide table
| |
| Illustration 4 | g01240891 |
Analog Sensor Connector (passive)
Show/hide table
| |
| Illustration 5 | g01241538 |
Connectors for the Termination Resistor
Show/hide table
| |
| Illustration 6 | g01355248 |
Show/hide table
| |
| Illustration 7 | g01155187 |
Show/hide table
| |
| Illustration 8 | g02219254 |
|
Refer to Special Instruction, REHS2556 for additional information | |
Show/hide table
| |
| Illustration 9 | g02220494 |
|
Refer to Tool Operating Manual, SEHS9615, "Servicing Deutsch HD and DT Style Connectors" for additional information | |
Information System:
G3600 A4 Engines
Engine Valve Lash - Check
G3600 A4 Engines
Engine Air Cleaner Element (Single Element) - Inspect/Clean/Replace
G3600 A4 Engines
Cylinder Pressure - Test/Record
Quick Start Wiring Guide for Dynamic Gas Blending Well Service Engines{1000, 1408, 1900, 1901, 7610, 7620}
G3600 A4 Engines
Coolant Level - Check
G3600 A4 Engines
Coolant (NGEC) - Change
C15 and C18 Engines for Caterpillar Built Machines
Programmable Parameters
C13 and C15 Generator Sets
Generator Start-up Checklist
2013/11/04
New Boost Pressure Sensor Location Is Used for Certain 3512 Petroleum Engines {1408, 1439, 1917}
CX31 and CX31 HT On-Highway Transmissions
Reference Material
C15 and C18 Engines for Caterpillar Built Machines
ECM - Replace
CX31 and CX31 HT On-Highway Transmissions
Capacities (Refill)
C15 and C18 Engines for Caterpillar Built Machines
Alternator Problem
374F and 390F Excavators and 390F MHPU Mobile Hydraulic Power Unit
Event Codes
C15 and C18 Engines for Caterpillar Built Machines
Coolant Contains Oil
C15 and C18 Engines for Caterpillar Built Machines
Coolant Contains Fuel
G3600 A4 Engines
Spark Plugs - Inspect/Adjust/Replace
C4.4 Industrial Engine
High Pressure Fuel Lines
G3600 A4 Engines
Model View Illustrations
2013/12/19
A New Power Distribution Box is Now Available and is Now Shipped Loose with Certain 3512C and 3516C Marine Engines {1408, 4460}
C18 Industrial Engines
Gauges and Indicators
C4.4 Industrial Engine
Electrical System
C27 and C32 Engines for Caterpillar Built Machines
Electronic Service Tool Does Not Communicate
G3306B Gas Engines
Piston and Rings