Diagnostic Code Cross Reference
`
C32 Marine Engines
[RENR9303]
C32 Marine Engines
System Configuration Parameters
C32 Marine Engines
Analog Sensor Supply Circuit - Test
ELECTRICAL AND STARTING SYSTEM
ELECTRONICS GP-ENGINE
C15 and C18 Petrolem Generator Set Engines
System Overview
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers
Electronic Service Tool Will Not Communicate with ECM
C27 and C32 Generator Set Engines
Diagnostic Codes
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers
ECM Will Not Communicate with Other Systems or Display Modules
C9 Marine Engines
Replacing the ECM
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers
Flash Programming
1.1. Cross-Reference for Flash Code to CID-FMI (Diagnostics) or EID (Events)
2.1. Cross-Reference for SPN-FMI Code to CID-FMI (Diagnostics) or EID (Events)
Problems with the electronic control system are reported via these types of codes: flash codes, SPN/FMI codes, diagnostic codes, and event codes.
For information on flash codes, refer to Troubleshooting, "Flash Codes".
For information on SPN/FMI codes, refer to Troubleshooting, "Diagnostic Codes".
For information on diagnostic codes, refer to Troubleshooting, "Diagnostic Codes".
For information on event codes, refer to Troubleshooting, "Event Codes".
Cross-Reference for Flash Code to CID-FMI (Diagnostics) or EID (Events)
Portions of this material are reprinted with permission from SAE J1939DA_201607© 2016 SAE International. SAE International is not responsible for any use or translation of this material, in whole or in part. Please contact SAE International to obtain a complete copy of SAE J1939DA_201607, the official definitive source of this standard.
Show/hide table
| Cross-Reference for Flash Code to CID-FMI (Diagnostics) or EID (Events) | ||
|---|---|---|
| Flash Code | CID-FMI or EID | Description of Code |
| 13 | 174-03 | Fuel Temperature open/short to +batt |
| 174-04 | Fuel Temperature short to ground | |
| 15 | 96-03 | Fuel Level Sensor open/short to +batt |
| 96-04 | Fuel Level Sensor short to ground | |
| 21 | 262-03 | 5 Volt Sensor DC Power Supply short to +batt |
| 262-04 | 5 Volt Sensor DC Power Supply short to ground | |
| 41-03 | 8 Volt DC Supply short to +batt | |
| 41-04 | 8 Volt DC Supply short to ground | |
| 24 | 100-03 | Engine Oil Pressure open/short to +batt |
| 100-04 | Engine Oil Pressure short to ground | |
| 25 | 102-03 | Boost Pressure Sensor open/short to +batt |
| 102-04 | Boost Pressure Sensor short to ground | |
| 27 | 110-03 | Engine Coolant Temperature open/short to +batt |
| 110-04 | Engine Coolant Temperature short to ground | |
| 28 | 91-13 | Throttle Position Calibration required |
| 1249-13 | Secondary Throttle Position calibration required | |
| 32 | 91-08 | Throttle Position signal abnormal |
| 1249-08 | Secondary Throttle Position signal abnormal | |
| 34 | 190-08 | Engine Speed abnormal |
| 320-02 | Speed/Timing Sensor Loss of Signal | |
| 320-11 | Speed/Timing Sensor mechanical failure | |
| 342-08 | Secondary Engine Speed signal abnormal | |
| 35 | E190 | Engine Overspeed Warning |
| 36 | E268 | Unexpected Engine Shutdown |
| 37 | 94-03 | Fuel Pressure open/short to +batt |
| 94-04 | Fuel Pressure short to ground | |
| 38 | 172-03 | Inlet Manifold Air Temp open/short to +batt |
| 172-04 | Inlet Manifold Air Temp short to ground | |
| 42 | 261-13 | Engine Timing Calibration required |
| 46 | E039 | Low Engine Oil Pressure Derate |
| E100 | Low Engine Oil Pressure Warning | |
| 51 | 168-02 | System Voltage intermittent/erratic |
| 58 | E057 | Low Engine Coolant Level Derate |
| E059 | Low Engine Coolant Level Warning | |
| 59 | 253-02 | Personality Module mismatch |
| 61 | E015 | High Engine Coolant Temperature Derate |
| E017 | High Engine Coolant Temperature Warning | |
| 63 | E053 | Low Fuel Pressure Warning |
| 64 | E025 | High Inlet Air Temperature Derate |
| E027 | High Inlet Air Temperature Warning | |
| 66 | E030 | High Transmission Oil Temperature Warning |
| 67 | 177-03 | Transmission Oil Temperature open/short to +batt |
| 177-04 | Transmission Oil Temperature short to ground | |
| 68 | 127-03 | Transmission Oil Pressure open/short to +batt |
| 127-04 | Transmission Oil Pressure short to ground | |
| 69 | E113 | High Transmission Oil Pressure |
| 71 | 1-05 | Injector Cylinder 1 open circuit |
| 1-06 | Injector Cylinder 1 short | |
| 72 | 2-05 | Injector Cylinder 2 open circuit |
| 2-06 | Injector Cylinder 2 short | |
| 73 | 3-05 | Injector Cylinder 3 open circuit |
| 3-06 | Injector Cylinder 3 short | |
| 74 | 4-05 | Injector Cylinder 4 open circuit |
| 4-06 | Injector Cylinder 4 short | |
| 75 | 5-05 | Injector Cylinder 5 open circuit |
| 5-06 | Injector Cylinder 5 short | |
| 76 | 6-05 | Injector Cylinder 6 open circuit |
| 6-06 | Injector Cylinder 6 short | |
| 77 | 7-05 | Injector Cylinder 7 open circuit |
| 7-06 | Injector Cylinder 7 short | |
| 78 | 8-05 | Injector Cylinder 8 open circuit |
| 8-06 | Injector Cylinder 8 short | |
| 81 | 9-05 | Injector Cylinder 9 open circuit |
| 9-06 | Injector Cylinder 9 short | |
| 82 | 10-05 | Injector Cylinder 10 open circuit |
| 10-06 | Injector Cylinder 10 short | |
| 83 | 11-05 | Injector Cylinder 11 open circuit |
| 11-06 | Injector Cylinder 11 short | |
| 84 | 12-05 | Injector Cylinder 12 open circuit |
| 12-06 | Injector Cylinder 12 short | |
Cross-Reference for SPN-FMI Code to CID-FMI (Diagnostics) or EID (Events)
Show/hide table
| Cross-Reference for SPN(1)-FMI Code to CID-FMI (Diagnostics) or EID (Events) | ||
|---|---|---|
| SPN/FMI Code | CID-FMI or EID | Description of Code |
| 29-08 | 1249-08 | Secondary Throttle Position signal abnormal |
| 29-13 | 1249-13 | Secondary Throttle Position calibration required |
| 91-08 | 91-08 | Throttle Position signal abnormal |
| 91-13 | 91-13 | Throttle Position calibration required |
| 94-03 | 94-03 | Fuel Pressure open/short to +batt |
| 94-04 | 94-04 | Fuel Pressure short to ground |
| 94-17 | E053 | Low Fuel Pressure Warning |
| 96-03 | 96-03 | Fuel Level Sensor open/short to +batt |
| 96-04 | 96-04 | Fuel Level Sensor short to ground |
| 96-17 | E119 | Low Fuel Level |
| 100-03 | 100-03 | Engine Oil Pressure open/short to +batt |
| 100-04 | 100-04 | Engine Oil Pressure short to ground |
| 100-17 | E100 | Low Engine Oil Pressure Warning |
| 100-18 | E039 | Low Engine Oil Pressure Derate |
| 102-03 | 102-03 | Boost Pressure Sensor open/short to +batt |
| 102-04 | 102-04 | Boost Pressure Sensor short to ground |
| 110-03 | 110-03 | Engine Coolant Temperature open/short to +batt |
| 110-04 | 110-04 | Engine Coolant Temperature short to ground |
| 110-15 | E017 | High Engine Coolant Temperature Warning |
| 110-16 | E015 | High Engine Coolant Temperature Derate |
| 111-17 | E059 | Low Engine Coolant Level Warning |
| 111-18 | E057 | Low Engine Coolant Level Derate |
| 127-03 | 127-03 | Transmission Oil Pressure open/short to +batt |
| 127-04 | 127-04 | Transmission Oil Pressure short to ground |
| 127-15 | E113 | High Transmission Oil Pressure |
| 127-17 | E046 | Low Transmission Oil Pressure Warning |
| 168-02 | 168-02 | System Voltage intermittent/erratic |
| 172-03 | 172-03 | Intake Manifold Air Temp open/short to +batt |
| 172-04 | 172-04 | Intake Manifold Air Temp short to ground |
| 172-15 | E027 | High Inlet Air Temperature Warning |
| 172-16 | E025 | High Inlet Air Temperature Derate |
| 174-03 | 174-03 | Fuel Temperature open/short to +batt |
| 174-04 | 174-04 | Fuel Temperature short to ground |
| 174-15 | E056 | High Fuel Temperature Warning |
| 177-03 | 177-03 | Transmission Oil Temperature open/short to +batt |
| 177-04 | 177-04 | Transmission Oil Temperature short to ground |
| 177-15 | E030 | High Transmission Oil Temperature Warning |
| 190-00 | E004 | Engine Overspeed Shutdown |
| 190-02 | 320-02 | Speed Timing/Sensor Loss of Signal |
| 190-08 | 190-08 | Engine Speed abnormal |
| 190-11 | 320-11 | Speed/Timing Sensor mechanical failure |
| 228-13 | 261-13 | Engine Timing Calibration required |
| 253-02 | 253-02 | Personality Module mismatch |
| 620-03 | 262-03 | 5 Volt Sensor DC Power Supply short to +batt |
| 620-04 | 262-04 | 5 Volt Sensor DC Power Supply short to ground |
| 651-05 | 1-05 | Injector Cylinder 1 open circuit |
| 651-06 | 1-06 | Injector Cylinder 1 short |
| 652-05 | 2-05 | Injector Cylinder 2 open circuit |
| 652-06 | 2-06 | Injector Cylinder 2 short |
| 653-05 | 3-05 | Injector Cylinder 3 open circuit |
| 653-06 | 3-06 | Injector Cylinder 3 short |
| 654-05 | 4-05 | Injector Cylinder 4 open circuit |
| 654-06 | 4-06 | Injector Cylinder 4 short |
| 655-05 | 5-05 | Injector Cylinder 5 open circuit |
| 655-06 | 5-06 | Injector Cylinder 5 short |
| 656-05 | 6-05 | Injector Cylinder 6 open circuit |
| 656-06 | 6-06 | Injector Cylinder 6 short |
| 657-05 | 7-05 | Injector Cylinder 7 open circuit |
| 657-06 | 7-06 | Injector Cylinder 7 short |
| 658-05 | 8-05 | Injector Cylinder 8 open circuit |
| 658-06 | 8-06 | Injector Cylinder 8 short |
| 659-05 | 9-05 | Injector Cylinder 9 open circuit |
| 659-06 | 9-06 | Injector Cylinder 9 short |
| 660-05 | 10-05 | Injector Cylinder 10 open circuit |
| 660-06 | 10-06 | Injector Cylinder 10 short |
| 661-05 | 11-05 | Injector Cylinder 11 open circuit |
| 661-06 | 11-06 | Injector Cylinder 11 short |
| 662-05 | 12-05 | Injector Cylinder 12 open circuit |
| 662-06 | 12-06 | Injector Cylinder 12 short |
| 678-03 | 041-03 | 8 Volt DC Supply short to +batt |
| 678-04 | 041-04 | 8 Volt DC Supply short to ground |
| 723-08 | 342-08 | Secondary Engine Speed signal abnormal |
| 1383-11 | E268 | Unidentified Shutdown |
Show/hide table
| (1) | Suspect Parameter Number |
Information System:
3408C and 3412C Marine Auxiliary and Marine Generator Set Engines
Refill Capacities and Recommendations
345C Excavator Machine System Specifications
Stick - 3.4 m (11.16 ft)
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines
Rocker Shaft and Pushrod - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines
Fuel Injection Nozzles - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines
Fuel Injection Pump - Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines
Fuel Injection Lines - Remove and Install
3508C, 3512C and 3516C Marine Engines
Piston Cooling Jets - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines
Rocker Shaft and Pushrod - Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines
Crankshaft Pulley - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines
Fuel Injection Pump - Remove
2004/12/01
Lifting Brackets and Hardware are Available {1122}
Installation of 262-6141 Alarm Gp {7406}
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines
Rocker Shaft - Assemble
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines
Crankcase Breather - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines
Inlet and Exhaust Valve Springs - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines
Inlet and Exhaust Valves - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines
Exhaust Manifold - Remove and Install
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines
Fuel Transfer Pump - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines
Fuel Transfer Pump - Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines
Rocker Shaft - Disassemble
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines
Pistons and Connecting Rods - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines
Camshaft - Remove
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines
Fuel Filter Base - Remove
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines
Camshaft - Install