Air Inlet and Exhaust Lines
`
3512B and 3516B Generator Set Engines with Dynamic Gas Blending
[KENR9742]
3512B and 3516B Generator Set Engines with Dynamic Gas Blending
Camshaft Bearing Position
3512B and 3516B Generator Set Engines with Dynamic Gas Blending
Air Inlet and Exhaust Lines
AIR INLET AND EXHAUST SYSTEM
EXHAUST GP
3512B and 3516B Generator Set Engines with Dynamic Gas Blending
Air Inlet and Exhaust Lines
3512B and 3516B Generator Set Engines with Dynamic Gas Blending
Air Inlet and Exhaust Lines
3512B and 3516B Generator Set Engines with Dynamic Gas Blending
Air Inlet and Exhaust Lines
3512B and 3516B Generator Set Engines with Dynamic Gas Blending
Air Inlet and Exhaust Lines
3512B and 3516B Generator Set Engines with Dynamic Gas Blending
Air Inlet and Exhaust Lines
Show/hide table
| |
| Illustration 1 | g03484818 |
|
Rear view | |
Show/hide table
| |
| Illustration 2 | g03484821 |
|
Bolt tightening sequence | |
Show/hide table
| Specification for 419-5447 Air Lines Gp | |||
| Item | Qty | Part | Specification Description |
| 1 | 8 | 6V-3917 O-Ring Seal | Before assembly, lubricate the bore lightly with 5P-3975 Rubber Lubricant. |
| 2 | 4 | 3J-5389 Plug | Before assembly, apply Loctite C5A Copper Anti-Seize to the threads.
Torque to |
| 3 | 8 | 6V-1943 High Temperature Bolt | Before assembly, apply Loctite C5A Copper Anti-Seize to the threads and bearing surfaces.
Torque to |
| 3 | 10 | 9F-2773 Bolt | Use the following procedure in order to assemble the aftercooler assembly and tighten the bolts:
1. Assemble the seals to the aftercooler core. 2. Temporarily secure the bottom seal to the aftercooler with tape. Do not use an adhesive, a silicone lubricant, or any other lubricant for retention of the seal. 3. Assemble the aftercooler with seals to the inlet manifold. 4. Inspect the bottom seal in order to ensure that the seal is seating correctly in the recess. 5. Install the aftercooler cover. 6. Inspect the upper seal in order to ensure that the seal is seating correctly in the recess. 7. Install the cover bolts. Hand tighten the cover bolts. 8. Tighten the bolts in a numerical sequence that is shown in Illustration 2 to 9. Again, tighten the bolts in a numerical sequence that is shown in Illustration 2 to 10. Remove the tape. |
| 5 | 12 | 6V-5101 O-Ring Seal | Before assembly, lubricate the bore lightly with 5P-3975 Rubber Lubricant. |
Information System:
UPS 300, UPS 301, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supplies
Electrical Connections
C13 and C15 Generator Sets
Safety Messages
320D2 Excavator Machine Electronic Control System
Diagnostic Capabilities
306, 306 CR, and 306.5 Mini Hydraulic Excavators
Final Drive Oil - Change
320D2 Excavator Machine Electronic Control System
Service Tools
306, 306 CR, and 306.5 Mini Hydraulic Excavators
High Pressure Fuel Lines
794 AC, 796 AC, and 798 AC Off-Highway Truck Electronic Control System
System Schematic
C18 Marine Engines
Refill Capacities
3500 Engines
Flywheel Housing
G3306B Petroleum Generator Set Engines
Timing - Calibrate
G3500J Petroleum Engines
Engine Oil Filter
2014/07/18
New Power Distribution Panel Groups are Used On Certain Tier 2 3508, 3512, and 3516 Marine Engines {4493, 7451, 7490}
C18 Petroleum Engine
Maintenance Interval Schedule
Disassembly and Assembly Procedure for 3N-8891 Sea Water Heat Exchanger Gp {1379}
Bench Test Procedure for a CX31 On Highway Truck or AD22 Articulated Truck Transmission {3030, 3073}
14L Motor Grader Machine Systems
Centershift Lock Bar and Bushings - Install
C18 Petroleum Engine
Product Description
14L Motor Grader Machine Systems
Centershift Lock Bar and Bushings - Remove
C18 Petroleum Engine
Gauges and Indicators
C18 Petroleum Engine
Monitoring System
Retrofit SCR Aftertreatment
Catalyst (SCR) - Replace
EMCP4.1/EMCP4.2
Integrated Voltage Regulator
Retrofit SCR Aftertreatment
Exhaust Outlet Nitrogen Oxide Sensor - Inspect/Replace
12M Series 3, 140M Series 3, 160M Series 3, 140, 150 and and 160 Motor Graders
Brake Control Valve (Service)