345C Excavator Machine System Specifications Stick Caterpillar

Stick

345C Excavator Machine System Specifications [RENR7323]

345C Excavator Machine System Specifications Stick

345C Excavator Machine System Specifications Stick - 3.0 m (9.84 ft)

Show/hide table




Illustration 1	g02882056
Typical example Right side view

Show/hide table

Table 1
Item	Qty	Part	Specification Description
-	All bores must be free of paint. Use 5P-0960 Grease Cartridge in order to coat all bores for the pins, the stick, the upper frame, the bushings, and the cylinder pin bores. After you assemble the bushings, coat all the bores and the bushings with 5P-0960 Grease Cartridge.
1	-	-	Stick cylinder must be assembled in order to orient the grease zerk, as shown in Illustration 1.
2	Install one shim and one spacer to the bracket that is next to each bucket cylinder, as shown in Illustration 1:
	2	133-2427 Shim	Thickness is 0.5 mm (0.02 inch).
	2	134-8944 Spacer	Thickness is 5.0 mm (0.20 inch).
3	2	130-4360 Pin As	Diameter is 99.85 ± 0.04 mm (3.931 ± 0.002 inch).
4	As required, use the following shims to adjust the maximum lateral clearance of 1.0 mm (0.04 inch):
	1	133-2427 Shim	Thickness is 0.5 mm (0.02 inch).
	2	093-0090 Shim	Thickness is 1.0 mm (0.04 inch).
	1	093-0122 Shim	Thickness is 2.0 mm (0.08 inch).
5	As required, use the following shims to adjust the maximum lateral clearance of 1.0 mm (0.04 inch):
	1	133-2427 Shim	Thickness is 0.5 mm (0.02 inch).
	2	093-0090 Shim	Thickness is 1.0 mm (0.04 inch).
	1	093-0122 Shim	Thickness is 2.0 mm (0.08 inch).
6	2	228-5621 Bushing⁽¹⁾	Bore before assembly is 120.259 ± 0.040 mm (4.7346 ± 0.0016 inch). Installation depth is 9.5 ± 0.8 mm (0.37 ± 0.03 inch).
7	4	9X-4599 Lip Type Seal	Lubricate the sealing lip lightly with the lubricant that is being sealed. Install the dust seal so that the lip faces outside, as shown. Install lip type seals so that the lip type seals do not extend beyond the face of the boss.
8	2	166-1494 Lip Type Seal	Lubricate the sealing lip lightly with the lubricant that is being sealed. Install the dust seal so that the lip faces outside, as shown. Install lip type seals so that the lip type seals do not extend beyond the face of the boss.
9	2	462-2005 Bushing⁽¹⁾	Bore before assembly is 80.181 ± 0.020 mm (3.1567 ± 0.0008 inch). Installation depth is 9.5 ± 0.8 mm (0.37 ± 0.03 inch)
10	2	228-5621 Bushing⁽¹⁾	Bore before assembly is 120.259 ± 0.040 mm (4.7346 ± 0.0016 inch). Installation depth is 9.5 ± 0.8 mm (0.37 ± 0.03 inch).
10	2	282-4716 Bearing⁽¹⁾⁽²⁾	Bore before assembly is 120.26 ± 0.02 mm (4.735 ± 0.001 inch). Installation depth is 15.0 mm (0.59 inch).