Boom
`
345C Excavator Machine System Specifications
[RENR7323]
345C Excavator Machine System Specifications
Final Drive
345C Excavator Machine System Specifications
Stick
Show/hide table
| |
| Illustration 1 | g02879418 |
|
Right side view Typical example | |
Show/hide table
| Item | Qty | Part | Specification Description |
|---|---|---|---|
| - | All bores must be free of paint. Use 5P-0960 Grease Cartridge in order to coat all bores for the pins, the stick, the upper frame, the bushing, and the cylinder pin bores. After you assemble the bushings, coat all the bores and the bushings with 5P-0960 Grease Cartridge. | ||
| 1 | 1 | 130-4360 Pin As | Diameter is |
| 2 | As required, use the following shims to adjust the maximum lateral clearance of |
||
| 1 | 133-2427 Shim | Thickness is |
|
| 2 | 093-0090 Shim | Thickness is |
|
| 1 | 093-0122 Shim | Thickness is |
|
| 3 | 1 | 148-3391 Pin | Diameter is |
| 4 | 2 | 9X-4600 Lip Type Seal | Lubricate the sealing lip lightly with the lubricant that is being sealed. Install the dust seal so that the lip faces outside, as shown. Install lip type seals so that the lip type seals do not extend beyond the face of the boss. |
| 5 | 2 | 228-5622 Bushing | Bore is Installation depth is |
| 6 | 1 | Pin As | Diameter is |
| 7 | As required, use the following shims to adjust the maximum lateral clearance of |
||
| 1 | 147-3957 Shim | Thickness is |
|
| 2 | 093-0074 Shim | Thickness is |
|
| 1 | 093-0106 Shim | Thickness is |
|
| - | Use 5P-0960 Grease Cartridge in order to fill with grease through the 3B-8489 Grease Fitting (9) after mounting the pin at the boom foot. Before you install the 8T-6764 Pipe Plug (8), make sure that the grease flows out of the pipe plug hole. | ||
Information System:
345C Excavator Machine System Specifications
Final Drive
C7 Engines for Caterpillar Built Machines
Connecting Rod Bearings - Install
C9 Marine Generator Set
Product Lifting
C32 Marine Engines
System Configuration Parameters
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers
Flash Programming
12M, 140, 140M and 160M Motor Graders Braking and Hydraulic Fan System
Brake and Hydraulic Fan System
C9 Engines for Caterpillar Built Machines
Basic Engine
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines
Housing (Front) - Disassemble
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines
Housing (Front) - Assemble
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines
Engine Oil Cooler - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines
Turbocharger - Remove and Install
C9 Marine Generator Set
Plate Locations and Film Locations
3508C, 3512C and 3516C Marine Engines
Accessory Drive (Front) - Disassemble
3508C, 3512C and 3516C Marine Engines
Accessory Drive (Front) - Assemble
3508C, 3512C and 3516C Marine Engines
Flywheel - Remove and Install
3126B Petroleum Engine
Diagnostic Code Cross Reference
12M, 140, 140M, 150, 160M and 160 Motor Graders Hydraulic and Steering System
Calibration Procedures
3508B, 3512B and 3516B Generator Set Engines
Flywheel Housing - Remove
3508B, 3512B and 3516B Generator Set Engines
Flywheel Housing - Install
2004/12/01
New Lockwasher Will Improve Varistor Reliability {4466}
C4.4 Industrial Engine
Electrical System
C11 and C13 Engines for Caterpillar Built Machines
General Information
C11 and C13 Engines for Caterpillar Built Machines
Lubrication System
G3520C and G3520E Generator Set Engines
Fuel Control Valve - Remove and Install