Heat Exchanger
`
C32 Commercial Engines
[SENR9772]
COOLING SYSTEM
HEAT EXCHANGER GP
C32 Commercial Engines
Heat Exchanger
C32 Commercial Engines
Heat Exchanger
Show/hide table
| |
| Illustration 1 | g02587497 |
|
Front view of engine | |
Show/hide table
| |
| Illustration 2 | g01114866 |
|
Tightening sequence | |
Show/hide table
| Specification for 284-3695 Sea Water Heat Exchanger Gp | |||
| Item | Qty | Part | Specification Description |
| 1 | 10 | 5P-4625 Bolt | Use the following procedure to tighten the bolts.
1. Install guide studs, washers, and nuts in locations (5) and (6). Hand tighten bolt (1) through bolt (4) in the numerical sequence as shown in Illustration 2. Use three incremental steps to tighten the bolts. 2. Remove the guide studs from locations (5) and (6). 3. Install the spacers (2) in locations (5) and (6). 4. Tighten bolt (1) through bolt (10) in the numerical sequence as shown in Illustration 2. |
| 2 | 2 | 166-4392 Special Spacer | |
Information System:
C15 and C18 Engines for Caterpillar Built Machines
Fuel Transfer Pump - Remove
12M, 140M, 160M, 140, 150 and 160 Motor Graders Hydraulic and Steering System
Hydraulic Tank
C27 and C32 Industrial and Petroleum Engines
Flywheel Housing
390F MHPU Mobile Hydraulic Power Unit
Engine Oil Level - Check
390F MHPU Mobile Hydraulic Power Unit
Cooling System Coolant Sample (Level 1) - Obtain
C15 and C18 Engines for Caterpillar Built Machines
Fuel System
C27 and C32 Generator Set Engines
Flywheel
G3520C and G3520E Generator Set Engines
Cooling System - Landfill Application
12M, 140, 140M, 150, 160M and 160 Motor Graders Hydraulic and Steering System
Blade Cushion - If Equipped
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines
Features
3500 Engines
Water Pump - Install
3500 Engines
Water Pump - Remove
3508C, 3512C and 3516C Marine Engines
Water Pump - Disassemble
3508C, 3512C and 3516C Marine Engines
Water Pump - Assemble
C27 and C32 Generator Set Engines
Electronic Unit Injector - Remove
C15 and C18 Engines for Caterpillar Built Machines
Electronic Unit Injector - Install
C27 and C32 Generator Set Engines
Electronic Unit Injector Sleeve - Remove
C9.3 Tier 4 Final Engines
Valve Mechanism
390D Excavator
Access Door and Cover Locations
G3406 and G3412 Generator Sets
Voltage Regulators
C27 and C32 Industrial and Petroleum Engines
Air Lines
2005/09/05
Improvements to Turbocharger and Exhaust Manifold Groups {1052, 1059, 1061}
3508B, 3512B and 3516B Generator Set Engines
Aftercooler - Remove and Install
2007/04/30
A New Oversized Oil Pump Idler Gear Shaft is Available {1304}