Installation Procedure For The Improved 377-2167 Water Lines Gp {1380}
[REHS8233]
COOLING SYSTEM
LINES GP-WATER
Installation Procedure For The Improved 377-2167 Water Lines Gp {1380}
1.1. Introduction
2.1. Installation Procedure
- Engine:
- G3520B (S/N: GLF1100-UP)
- Petroleum Engine:
- G3520B PETROLEUM (S/N: TPC140-140,1002-UP)
Introduction
Use this procedure to install the additional mounting clips on the 377-2167 Water Lines Gp .
Installation Procedure
- Remove clamps (1) .
Show/hide table
 | |
| Illustration 1 | g03494142 |
(1) 208-6270 Clamps | |
- Install clips (2) and (3).
Show/hide table
 | |
| Illustration 2 | g03495358 |
(2) 6V-1581 Clips (3) 6V-1582 Clips (4) 0L-1143 Bolts (5) 9X-6458 Hard Washers (6) 9S-8752 Nuts (7) 205-6716 Spacers | |
- Attach two pairs of clips (2) and (3) using one bolt (4), two washers (5), and one nut (6). Install one spacer (7) in between the pair of clips.
- Install one clip (2) and one clip (3).
Show/hide table
 | |
| Illustration 3 | g03495500 |
(2) 6V-1581 Clip (3) 6V-1582 Clip (5) 9X-6458 Hard Washers (6) 9S-8752 Nuts (8) 4P-9029 Bracket (9) 0S-1591 Bolt (10) 0S-1619 Bolt (11) 8B-2026 Spacer | |
- Install bracket (8). Attach bracket (8) to clips (2) and (3) using one bolt (9), two washers (5), and one nut (6) .
- Attach bracket (8) to the oil fill elbow using one bolt (10), one washer (5) and one spacer (11) .
Information System:
2013/10/31
Improved Water Lines Group For Certain G3520B Engines {1380}
2013/11/13
Cylinder Head Gasket Torque Procedures for Certain 3500 Engines {1100, 1124}
2013/11/12
Cylinder Head Gasket Torque Procedures for Certain3500 Machine Engines {1100, 1124}
C32 Marine Generator Set
Maintenance Interval Schedule
C9 Petroleum Engine
Fluid Recommendations
C9 Petroleum Engine
Refill Capacities
Inspection Criteria for MMUs Experiencing Load Cell - CM Errors{4480}
XQC1200 Power Module
Before Starting Engine
XQC1600 Power Module
Electronic Modular Control Panel 4 (EMCP 4)
Retrofit SCR Aftertreatment
Catalyst (SCR) - Clean/Inspect
C7 Petroleum Engine
Maintenance Interval Schedule
XQC1600 Power Module
Plate Locations and Film Locations
C13 and C15 Generator Sets
Refill Capacities
Three60 Precision Control System
Configuration Parameters
12M Series 3, 140M Series 3, 160M Series 3, 140, 150 and 160 Motor Graders
Diagnostic Trouble Codes
C4.4 Industrial Engine
Coolant (ELC) - Change
2014/01/13
New Jacket Water Heater Groups Are Used on Certain 3500 Engines {1383}
794 AC, 796 AC, and 798 AC Off-Highway Truck Electronic Control System
Diagnostic Trouble Codes
3512B and 3516B Generator Set Engines with Dynamic Gas Blending
Water Temperature Regulator
2013/12/10
A New Cable Assembly for the Powered Access Stairway Is Now Used on Certain Off-Highway Trucks {7254}
Procedure for Removing and Installing the Exhaust Cooler (NRS) on All Tier 4 C15 and C18 Engines {108C, 108G}
3512B and 3516B Generator Set Engines with Dynamic Gas Blending
Radiator
2013/10/24
New Software for the Turbocharger Protection Strategy on the C4.4 Engine {1052, 1920}
3512B and 3516B Generator Set Engines with Dynamic Gas Blending
Air Shutoff