Maintenance Interval Schedule
`
C15 Petroleum Engine
[SEBU8400]
ENGINE ARRANGEMENT
When Required
Battery - ReplaceBattery or Battery Cable - Disconnect
Coolant Extender (ELC) - Add
Engine Air Cleaner Element (Dual Element) - Inspect/Clean/Replace
Engine Storage Procedure - Check
Fuel System - Prime
Daily
Coolant Level - CheckEngine Air Cleaner Service Indicator - Inspect
Engine Air Precleaner - Check/Clean
Engine Oil Level - Check
Fuel System Primary Filter/Water Separator - Drain
Fuel Tank Water and Sediment - Drain
Walk-Around Inspection
Initial 250 Service Hours
Engine Valve Lash - CheckEvery 250 Service Hours
Air Shutoff - TestCoolant Sample (Level 1) - Obtain
Cooling System Supplemental Coolant Additive (SCA) - Test/Add
Engine Oil and Filter - Change
Grounding Stud - Inspect/Clean/Tighten
Starting Motor - Inspect
Initial 500 Hours (for New Systems, Refilled Systems, and Converted Systems)
Coolant Sample (Level 2) - ObtainEvery 500 Service Hours
Belts - Inspect/Adjust/ReplaceTurbocharger - Inspect
Water Pump - Inspect
Every Year
Coolant Sample (Level 2) - ObtainEngine Valve Lash - Check
Every 3000 Service Hours or 3 Years
Coolant (DEAC) - ChangeElectronic Unit Injector - Check/Replace
Engine Protective Devices - Check
Engine Speed/Timing Sensor - Clean/Inspect
Every 6000 Service Hours or 6 Years
Coolant Temperature Regulator - ReplaceEvery 8000 Service Hours or 3 Years
Driven Equipment - CheckEvery 12 000 Service Hours or 6 Years
Coolant (ELC) - ChangeEvery 14 400 L (3750 US gal) of Fuel or 250 Service Hours or 1 Year
Engine Crankcase Breather - CleanEngine Oil Sample - Obtain
Fuel System Primary Filter (Water Separator) Element - Replace
Fuel System Secondary Filter - Replace
Hoses and Clamps - Inspect/Replace
Radiator - Clean
Every 114 000 L (30 000 US gal) of Fuel or 1500 Service Hours
Aftercooler Core - Clean/Test
Battery Electrolyte Level - Check
Every 170 400 L (45 000 US gal) of Fuel or 3000 Service Hours
Crankshaft Vibration Damper - InspectEngine - Clean
Engine Mounts - Inspect
Engine Valve Rotators - Inspect
Fan Drive Bearing - Lubricate
Every 380 000 L (100 000 US gal) of Fuel or 10 000 Service Hours
Overhaul Considerations
Overhaul
Fan Drive Bearing - ReplaceInformation System:
C4.4 Industrial Engine
Configuration Parameters
C4.4 Industrial Engine
Diagnostic Flash Code Retrieval
CX31-P600 Petroleum Transmission
Speed Sensor (Transmission)
Installation of Improved Relays for the Power Distribution Panel Used on Certain 3500 Marine Engines{4493, 7451, 7490}
G3306B Petroleum Generator Set Engines
Gas Pressure - Check and Adjust
G3306B Petroleum Generator Set Engines
Diagnostic Trouble Codes
G3306B Petroleum Generator Set Engines
Electronic Control Module (ECM)
2013/10/11
New Engine Monitoring System III Software Is Used on Certain 3500 Generator Set Engines {1901, 1920}
C280-12 Marine Engine
Product Lifting
C280-12 Marine Engine
Model View Illustrations
C280-12 Marine Engine
Safety Messages
CX31-P600 Petroleum Transmission
Transmission Control
CX31-P600 Petroleum Transmission
Power Train Electronic Control Module (Electronic Clutch Pressure Control)
390F MHPU Mobile Hydraulic Power Unit Machine System
Main Control Valve
CX31-P600 Petroleum Transmission
Power Train Pressures
390F MHPU Mobile Hydraulic Power Unit Machine System
Solenoid Valve (Proportional Reducing) - Power Shift System
CX31-P600 Petroleum Transmission
Transmission Oil Supply
CX31-P600 Petroleum Transmission
Relief Valve (Transmission Hydraulic Control) - Test and Adjust
CX31-P600 Petroleum Transmission
Relief Valve (Torque Converter Inlet) Pressure - Test
CX31-P600 Petroleum Transmission
Modulating Valve (Torque Converter Lockup Clutch) - Test
320D2 Forest Machine Machine System Specifications
Pressure Reducing Valve (Boom and Stick Priority)
12M Series 3, 140M Series 3, 160M Series 3, 140, 150 and and 160 Motor Graders
General Information (Fan Hydraulic System)
390F Excavator Machine Systems
Control Valve (Stick Lowering)
CX31-P600 Petroleum Transmission
Transmission Hydraulic Control - Dropbox