C12.9 Marine Engines Fumes Disposal Filter Element - Replace - External Caterpillar


Fumes Disposal Filter Element - Replace - External
`

Note: There are two fumes disposal filter elements on the engine. The external filter must be replaced at the stated interval. The internal/centrifugal filter must be replaced at every second replacement of the external filter.

The fumes disposal system requires the replacement of the fumes disposal filter. The service interval of the fumes disposal filter will be affected by the following items:

  • Engine load

  • Concentration of soot

  • Condition of the engine

------ WARNING! ------

Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact the skin.



NOTICE

Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.

Refer to Special Publication, NENG2500, "Cat Dealer Service Tool Catalog" or refer to Special Publication, PECJ0003, "Cat Shop Supplies and Tools Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.

Dispose of all fluids according to local regulations and mandates.




Illustration 1g06010630

  1. Remove the cover assembly (1).

  2. Remove the filter element.

  3. Replace the filter element.

  4. Install the cover assembly.

Information System:

Crimping XT-3 ES and XT-5 S4G, MCSH, and MCSX Couplings Using 4C-3660, 4C-5052, 4C-5053, 9U-5792, or 9U-7261 Hose Machines{0374, 0599, 0684, 0738, 5057}
C12.9 Marine Engines Fuel System Primary Filter/Water Separator - Drain
14L Motor Grader Machine Systems Fan and Gear Motor (Hydraulic Fan) - Remove and Install
Using the 223-2105 Hose Cutting Machine{0374, 0599, 0678, 0684, 0708, 0738, 5057, 6060}
307, 308, 309 and 310 EXCAVATOR Boom
Disassembly, Assembly, and Installation of the Oil Heater Pumps and Seals for Certain 3600 and C280 Engines{1333}
C12.9 Marine Engines Engine Oil and Filter - Change
C18 Generator Set Refill Capacities
2014/12/23 A New Outlet Elbow Is Used on Certain Machine Engines {1307}
2013/10/28 A New Outlet Elbow Is Available for Certain Commercial Engines {1307}
374F and 390F Excavators and 390F MHPU Mobile Hydraulic Power Unit Sensor Signal (Analog, Passive) - Test
374F and 390F Excavators and 390F MHPU Mobile Hydraulic Power Unit CAN Data Link - Test
C13 and C15 Generator Sets Single Unit Operation
C8.7 Marine Engine Heat Exchanger - Clean/Test
C9, C13, C15 and and C18 Generator Sets Voltage Regulators
TA2 Inspection for C7.1 Industrial Engine{0372, 1000, 7000, 753T, 7565}
12M Series 3, 140, 140M Series 3, 150, 160M Series 3 and and 160 Motor Graders Power Train Rear Axle, Differential and Final Drive - Assemble
14L Motor Grader Gear Pump (Transmission Charging and Scavenge) - Remove
14L Motor Grader Rear Axle, Differential and Final Drive - Disassemble
14L Motor Grader Gear Pump (Transmission Charging and Scavenge) - Install
14L Motor Grader Rear Axle, Differential and Final Drive - Install
14L Motor Grader Rear Axle, Differential and Final Drive - Remove
C8.7 Marine Engine Model View Illustrations
3600 and C280 Diesel Engine Fluids Recommendations Contamination Control