Clean the cooling system before the recommended maintenance interval if the following conditions exist:
- The engine overheats frequently.
- Foaming is observed.
- The oil has entered the cooling system and the coolant is contaminated.
| NOTICE |
|---|
|
Use of commercially available cooling system cleaners may cause damage to cooling system components. Use only cooling system cleaners that are approved for AVSpare engines. |
- Stop the engine and allow the engine to cool. Ensure that the engine will not start when the cooling system is drained.
- Loosen the cooling system filler cap slowly in order to relieve any pressure. Remove the cooling system filler cap.
Show/hide table
Illustration 1 g00792409 Location of cooling system drain valves or drain plugs on the water pumps
(1) Jacket water pump
(2) Aftercooler and oil cooler pumpShow/hide table
Illustration 2 g00901833 Location of drain plug for the jacket water system - Open the cooling system drain valves (if equipped). Remove the cooling system drain plugs. Allow the coolant to drain.
| NOTICE |
|---|
|
Dispose of used engine coolant properly or recycle. Various methods have been proposed to reclaim used coolant for reuse in engine cooling systems. The full distillation procedure is the only method acceptable by AVSpare to reclaim the used coolant. |
For information regarding the disposal and the recycling of used coolant, consult your Cat dealer or consult Cat Dealer Service Tools Group:
Outside Illinois 1-800-542-TOOLInside Illinois 1-800-541-TOOL
Canada 1-800-523-TOOL
- Flush the cooling system with clean water in order to remove any debris.
- Close the cooling system drain valves (if equipped). Clean the cooling system drain plugs and install the cooling system drain plugs.
Show/hide table
NOTICE Fill the cooling system no faster than
19 L (5 US gal) per minute in order to avoid air locks. Proper venting of the cooling system is essential to fill at this rate. - Fill the cooling system with a mixture of clean water and Cat Fast Acting Cooling System Cleaner. Add
.5 L (1 pt) of cleaner per15 L (4 US gal) of the cooling system capacity. Install the cooling system filler cap. - Start the engine. Operate the engine for a minimum of 30 minutes with a coolant temperature of at least
82 °C (180 °F) . - Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly in order to relieve any pressure. Remove the cooling system filler cap. Open the cooling system drain valves (if equipped). Remove the cooling system drain plugs. Allow the water to drain.
Show/hide table
NOTICE Improper or incomplete rinsing of the cooling system can result in damage to copper and other metal components.
To avoid damage to the cooling system, make sure to completely flush the cooling system with clear water. Continue to flush the system until all signs of the cleaning agent are gone.
- Flush the cooling system with clean water until the water that drains is clean. Close the cooling system drain valves (if equipped). Clean the cooling system drain plugs and install the cooling system drain plugs.
Cleaning a Cooling System that has Heavy Deposits or Plugging
Note: For the following procedure to be effective, there must be an active flow through the cooling system components.
- Flush the cooling system with clean water in order to remove any debris.
- Close the cooling system drain valves (if equipped). Clean the cooling system drain plugs and install the cooling system drain plugs.
- Fill the cooling system with a mixture of clean water and Cat Fast Acting Cooling System Cleaner. Add
.5 L (1 pt) of cleaner per3.8 to 7.6 L (1 to 2 US gal) of the cooling system capacity. Install the cooling system filler cap. - Start the engine. Operate the engine for a minimum of 90 minutes with a coolant temperature of at least
82 °C (180 °F) . - Stop the engine and allow the engine to cool. Loosen the cooling system filler cap slowly in order to relieve any pressure. Remove the cooling system filler cap. Open the cooling system drain valves (if equipped). Remove the cooling system drain plugs. Allow the water to drain.
Show/hide table
NOTICE Improper or incomplete rinsing of the cooling system can result in damage to copper and other metal components.
To avoid damage to the cooling system, make sure to completely flush the cooling system with clear water. Continue to flush the system until all signs of the cleaning agent are gone.
- Flush the cooling system with clean water until the water that drains is clean. Close the cooling system drain valves (if equipped). Clean the cooling system drain plugs and install the cooling system drain plugs.
| NOTICE |
|---|
|
Fill the cooling system no faster than |
Note: For information about the proper coolant to use, and the capacity of the cooling system, see this Operation and Maintenance Manual, "Refill Capacities and Recommendations" (Maintenance Section).
- Fill the cooling system with coolant/antifreeze. Do not install the cooling system filler cap.
- Start the engine. Operate the engine in order to purge the air from the cavities of the engine block. Allow the coolant to warm and allow the coolant level to stabilize. Stop the engine.
- Check the coolant level. Maintain the coolant to the proper level on the sight gauge (if equipped). If a sight gauge is not equipped, maintain the coolant to the level that is specified by the OEM of the cooling system.
- Clean the cooling system filler cap. Inspect the gaskets of the cooling system filler cap. If the gaskets of the cooling system filler cap are damaged, discard the old filler cap and install a new filler cap. If the gaskets of the cooling system filler cap are not damaged, use a 9S-8140 Pressurizing Pump to pressure test the filler cap. The correct pressure is stamped on the face of the cooling system filler cap. If the cooling system filler cap does not retain the correct pressure, install a new cooling system filler cap.
- Start the engine. Inspect the cooling system for leaks and for proper operating temperature.