Maintenance Interval Schedule - 3054 Turbocharged Marine Generator Set Engine
`
3054 and 3056 Marine Generator Sets
[SEBU7577]
3054 and 3056 Marine Generator Sets
Maintenance Interval Schedule - 3054 Naturally Aspirated Marine Generator Set Engine
3054 and 3056 Marine Generator Sets
Maintenance Interval Schedule - 3056 Turbocharged Marine Generator Set Engine
ENGINE ARRANGEMENT
Note: Before performing any operation or maintenance procedures, ensure that the Safety Information, warnings, and instructions are read and understood.
To determine the maintenance intervals, use fuel consumption, service hours, or calendar time, whichever occurs first . Experience has shown that maintenance intervals are most accurately scheduled on the basis of fuel consumption.
Before each consecutive interval is performed, all of the maintenance items from the previous interval must also be performed.
When Required
Battery - ReplaceBattery or Battery Cable - Disconnect
Engine - Clean
Fuel System - Prime
Generator Set - Test
Rotating Rectifier - Test
Daily
Cooling System Coolant Level - CheckElectrical Connections - Check
Engine Air Cleaner Service Indicator - Inspect
Engine Oil Level - Check
Generator Load - Check
Walk-Around Inspection
Every Week
Generator - InspectEvery 100 Service Hours or 3 Months
Insulation - TestEvery 500 Service Hours
Cooling System Coolant Sample (Level 1) - ObtainEvery Year
Cooling System Coolant Sample (Level 2) - ObtainFirst 470 L (125 US gal) of Fuel or First 20 to 40 Service Hours
Belts - Inspect/Adjust/Replace
Engine Valve Lash - Inspect/Adjust
Every 4450 L (1175 US gal) of Fuel or 250 Service Hours or 1 Year
Cooling System Supplemental Coolant Additive (SCA) - Test/Add
Every 4700 L (1250 US gal) of Fuel or 400 Service Hours or 1 Year
Auxiliary Water Pump (Rubber Impeller) - Inspect
Battery Electrolyte Level - Check
Cooling System Supplemental Coolant Additive (SCA) - Test/Add
Crankshaft Vibration Damper - Inspect
Engine Air Cleaner Element (Dual Element) - Clean/Replace
Engine Mounts - Inspect
Engine Oil Sample - Obtain
Engine Oil and Filter - Change
Fuel System Primary Filter (Water Separator) Element - Replace
Fuel System Secondary Filter - Replace
Fuel Tank Water and Sediment - Drain
Fuel Transfer Pump Strainer - Clean
Heat Exchanger - Inspect
Hoses and Clamps - Inspect/Replace
Every 23 500 L (6250 US gal) of Fuel or 2000 Service Hours or 2 Years
Alternator - Inspect
Cooling System Coolant (DEAC) - Change
Cooling System Water Temperature Regulator - Replace
Engine Crankcase Breather - Clean/Replace
Engine Valve Lash - Inspect/Adjust
Fuel Injection Nozzles - Test/Exchange
Generator - Dry
Starting Motor - Inspect
Turbocharger - Inspect/Clean
Water Pump - Inspect
Every 70 500 L (18 750 US gal) of Fuel or 6000 Service Hours
Cooling System Coolant (ELC) - Change
Every 7500 L (2000 US gal) of Fuel or 1000 Service Hours
Rotating Rectifier - Check
Every 117 500 L (31 250 US gal) of Fuel or 10 000 Service Hours
Overhaul Considerations
Every 28 500 L (7500 US gal) of Fuel or 3000 Service Hours
Cooling System Coolant Extender (ELC) - Add
Information System:
3508B, 3512B and 3516B Generator Set Engines
Air Inlet Manifold - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines
Crankshaft
C27 and C32 Engines for Caterpillar Built Machines
Cylinder Liner
2004/11/01
Improved Turbocharger Groups {1052}
C12 Marine Engines
Valve Mechanism Cover Base - Remove and Install
3126B Petroleum Engine
Cooling System - Check - Overheating
3508C, 3512C and 3516C Marine Engines
Engine Oil Filter Housing - Assemble
3508C, 3512C and 3516C Marine Engines
Engine Oil Filter Housing - Disassemble
C12 Marine Engines
Marine Transmission Oil Cooler - Remove and Install
345C MHPU Mobile Hydraulic Power Unit Hydraulic System
Solenoid Valve (Proportional Reducing) - Power Shift System
C27 and C32 Industrial and Petroleum Engines
Exhaust Manifold
3508C, 3512C and 3516C Marine Engines
Engine Oil Filter Housing - Install
3054 and 3056 Marine Generator Sets
Maintenance Interval Schedule - 3056 Turbocharged Marine Generator Set Engine
C27 and C32 Generator Set Engines
Piston and Rings
320D Excavator
Boom, Stick and Bucket Operation
C0.5 and C0.7 Industrial Engines
Engine Starting
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines
General Information
345C MHPU Mobile Hydraulic Power Unit Hydraulic System
Pilot Valve (Joystick)
3500 Engines
Water Pump - Remove
3500 Engines
Water Pump - Install
GENSET, SR4, SR4 HV, SR4B and SR4B HV Electric Power Generation, 3126, 3176B, 3176C, 3196, 3408E, 3412C, 3412E, 3508, 3508B, 3512, 3512B, 3516, 3516B and G3616 Engines, 3406E GEN SET Generator Set, 3406E IND, 3408C IND and 3456 IND Industrial Engines
Features
12M, 140, 140M, 150, 160M and 160 Motor Graders Hydraulic and Steering System
Blade Cushion - If Equipped
G3520C and G3520E Generator Set Engines
Cooling System - Landfill Application
C27 and C32 Generator Set Engines
Flywheel