Jacking Locations
`
12M and 140 Motor Grader
[SEBU9083]
MACHINE ARRANGEMENT
1.1. Front of the Machine
2.1. Rear of the Machine
Show/hide table
 |
|
Personal injury or death can result from improper lifting or blocking. When a jack is used to lift the machine, stand clear of the area. Use a jack that is rated for the correct capacity to lift the machine. Install blocks or stands before performing any work on the machine. |
Before the front of the machine is raised, verify the following information:
- The transmission is in the NEUTRAL position.
- Engage the parking brake.
- The wheel lean locking bolt is in the front axle.
- The frame lock pin is installed.
- The rear tires are chocked.
- The jack is sufficiently sized for the weight of the machine. See Operation and Maintenance Manual, "Specifications" for the weight of the machine.
Show/hide table
| |
| Illustration 1 | g01112402 |
|
Typical Example Shown | |
The location for jacking up the front of the machine is under the front axle.
Before the rear of the machine is raised, verify the following information:
- The transmission is in the NEUTRAL position.
- The wheel lean locking bolt is in the front axle.
- The frame lock pin is installed.
- The front tires are chocked.
- The jack is sufficiently sized for the weight of the machine. See Operation and Maintenance Manual, "Specifications" for the weight of the machine.
Show/hide table
| |
| Illustration 2 | g01112403 |
The location for jacking up the rear of the machine is under the main frame on the rear of the machine.
Information System:
330D, 336D and 340D Excavators Hydraulic System
Pump Control (Main Hydraulic) - Main Pump Regulator
Converting to Charge Density{1000}
On-Highway Engines Electronic PTO Installation and Application Guide
Remote PTO Accelerator Position Sensor Circuit - Test
On-Highway Engines Electronic PTO Installation and Application Guide
PTO Switch ON Lamp Circuit - Test
On-Highway Engines Electronic PTO Installation and Application Guide
PTO Switch Circuit - Test
On-Highway Engines Electronic PTO Installation and Application Guide
PTO Shutdown Timer - Test
Installation Procedure for 257-4183 Injector Wiring Harness Kit {1408}
G3516C and G3516E Gas Engines
Crankcase Breather
C9 Industrial Engines
Electronic Control System Components
C15 and C18 Industrial Engines
Fuel Pressure Sensor - Remove and Install
C15 and C18 Industrial Engines
Fuel Temperature Sensor - Remove and Install
C6.6 Marine Generator Set
Voltage Regulators
12M, 140, 140M and 160M Motor Graders Braking and Hydraulic Fan System
Machine Preparation for Troubleshooting
2004/10/01
New Ignition Transformers are Used {4476}
12M and 140 Motor Grader
Towing the Machine
12M and 140 Motor Grader
Braking System - Test
Asphalt Pavers Conveyor Electronic Control System
Electrical Connector - Inspect
374F Excavator
Ether Starting Aid Cylinder - Replace - If Equipped
12M, 140, 140M and 160M Motor Graders Braking and Hydraulic Fan System
Brake System Air - Purge
120M, 12M, 140, 140M, 150, 14M, 160M, 160 and 16M Motor Graders Secondary Steering System
Secondary Steering Electrical System
120M, 12M, 140, 140M, 150, 14M, 160M, 160 and 16M Motor Graders Secondary Steering System
Secondary Steering Hydraulic System
3508C, 3512C and 3516C Marine Engines
Fuel Transfer Pump - Disassemble
3508C, 3512C and 3516C Marine Engines
Fuel Transfer Pump - Assemble
3508B Engine for Caterpillar Built Machines
Refrigerant Compressor