2004/10/01 New Ignition Transformers are Used {4476} Caterpillar


New Ignition Transformers are Used {4476}
`
2004/10/01 [SEBD9338]
ELECTRICAL AND STARTING SYSTEM
TRANSFORMER GP
2004/10/01 New Ignition Transformers are Used {4476}
Engine:
G3508 (S/N: 2TJ1-UP; 4WD1-UP; 9AW1-UP; 9TG1-UP; CPJ1-UP; CPS1-UP; CPY1-UP; CTN1-UP)
G3512 (S/N: 5JD1-UP; 6JW1-UP; 7NJ1-UP; CRN1-UP; CSP1-UP; CTM1-UP)
G3516 (S/N: 4EK1-UP; 8LD1-UP; 8PW1-UP; CPG1-UP; CSZ1-UP; CTL1-UP)
G3524 (S/N: 5ZZ1-UP; 7SZ1-UP)
G3532 (S/N: 8BZ1-UP; 8JZ1-UP)

Description of Change: New ignition transformers are used for G3500 Engines that are equipped with the Electronic Ignition System (EIS). The new transformers have an improved design that is more robust, which improves the service life.

Adaptable To: The new transformers are direct replacement for the former transformers. Refer to Table 1 for the correct transformers for each ignition type. Table 2 lists the effective engines that are equipped with a standard ignition. Table 3 lists the effective engines that are equipped with a Canadian Standards Association (CSA) ignition.

Table 1
Ignition Type     Former Ignition Transformer     New Ignition Transformer    
Standard Ignition     165-1589     232-6346    
CSA Ignition     165-1590     232-6347    

Table 2
Effective Serial Numbers for Engines with Standard Ignition    
S/N:2TJ00179-UP     S/N:4EK04102-UP    
S/N:4WD00034-UP     S/N:5JD00106-UP    
S/N:5ZZ00270-UP     S/N:6JW00129-UP    
S/N:7NJ01058-UP     S/N:8JZ00306-UP    
S/N:8LD00137-UP     S/N:8PW00344-UP    
S/N:9TG00382-UP     S/N:CTL00766-UP    
S/N:CTM00348-UP     S/N:CTN00212-UP    

Table 3
Effective Serial Numbers for Engines with CSA Ignition    
S/N:4EK04164-UP     S/N:4WD00035-UP    
S/N:5JD00112-UP     S/N:7NJ01116-UP    
S/N:8LD00141-UP     S/N:9TG00387-UP    

Information System:

12M, 140, 140M and 160M Motor Graders Braking and Hydraulic Fan System Machine Preparation for Troubleshooting
12M and 140 Motor Grader Jacking Locations
330D, 336D and 340D Excavators Hydraulic System Pump Control (Main Hydraulic) - Main Pump Regulator
Converting to Charge Density{1000}
On-Highway Engines Electronic PTO Installation and Application Guide Remote PTO Accelerator Position Sensor Circuit - Test
On-Highway Engines Electronic PTO Installation and Application Guide PTO Switch ON Lamp Circuit - Test
On-Highway Engines Electronic PTO Installation and Application Guide PTO Switch Circuit - Test
On-Highway Engines Electronic PTO Installation and Application Guide PTO Shutdown Timer - Test
Installation Procedure for 257-4183 Injector Wiring Harness Kit {1408}
G3516C and G3516E Gas Engines Crankcase Breather
C9 Industrial Engines Electronic Control System Components
C15 and C18 Industrial Engines Fuel Pressure Sensor - Remove and Install
12M and 140 Motor Grader Towing the Machine
12M and 140 Motor Grader Braking System - Test
Asphalt Pavers Conveyor Electronic Control System Electrical Connector - Inspect
374F Excavator Ether Starting Aid Cylinder - Replace - If Equipped
12M, 140, 140M and 160M Motor Graders Braking and Hydraulic Fan System Brake System Air - Purge
120M, 12M, 140, 140M, 150, 14M, 160M, 160 and 16M Motor Graders Secondary Steering System Secondary Steering Electrical System
120M, 12M, 140, 140M, 150, 14M, 160M, 160 and 16M Motor Graders Secondary Steering System Secondary Steering Hydraulic System
3508C, 3512C and 3516C Marine Engines Fuel Transfer Pump - Disassemble
3508C, 3512C and 3516C Marine Engines Fuel Transfer Pump - Assemble
3508B Engine for Caterpillar Built Machines Refrigerant Compressor
C7 and C9 On-Highway Engines Poor Acceleration or Response
Cat</SUP> Digital Voltage Regulator Parameter Viewing and Configuration (Caterpillar PC Software)